SAGA Stepper Gauges- Help !!
#1
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jan 2010
Location: London
Posts: 1,179
Likes: 0
Received 0 Likes
on
0 Posts
SAGA Stepper Gauges- Help !!
I have a set of saga gauges as shown below:
I need a guide or manual on these urgently, my issue is that there is an over-boost alert from the boost gauge which is set too low.
I need to know how to change the setting on this but do not know how to do so. I have a little reset switch that you plug in the back of each gauge to reset them, tried fiddling around but still not too sure as it had not made a difference.
Advice needed urgently...
Thanks
Neel
I need a guide or manual on these urgently, my issue is that there is an over-boost alert from the boost gauge which is set too low.
I need to know how to change the setting on this but do not know how to do so. I have a little reset switch that you plug in the back of each gauge to reset them, tried fiddling around but still not too sure as it had not made a difference.
Advice needed urgently...
Thanks
Neel
#5
Scooby Regular
iTrader: (2)
Isn't there a website? Defi has a website with online downloadable instructions, I'd be surprised if these haven't?
Try here for instructions: sales@autodials.co.uk
http://www.autodials.co.uk/
Try here for instructions: sales@autodials.co.uk
http://www.autodials.co.uk/
#6
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jan 2010
Location: London
Posts: 1,179
Likes: 0
Received 0 Likes
on
0 Posts
I've had a look on that site Alcazar, not found anything...
Looked everywhere, not sure what to do.
Wondering if someone has the same gauges and still had the manual that came with it...
Thanks
Looked everywhere, not sure what to do.
Wondering if someone has the same gauges and still had the manual that came with it...
Thanks
#7
Scooby Regular
iTrader: (11)
If they're anything like the Prosport/Autogauges ones, the way to reset them would be:
"Push and hold the button until the pointer begins to flash. Release button. Then while the pointer is still flashing (set mode) push the button and hold it to move the pointer fast or each time you push the button the pointer will move in small increments to the exact point where you want to set it. After you have the pointer where you want to set your warning level just wait about 6 seconds and the pointer will stop flashing and retain that point as your new warning level. If you pass the point you wanted to set the level at-just keep going and once it reaches the end of the scale it will begin to come back."
HTH
"Push and hold the button until the pointer begins to flash. Release button. Then while the pointer is still flashing (set mode) push the button and hold it to move the pointer fast or each time you push the button the pointer will move in small increments to the exact point where you want to set it. After you have the pointer where you want to set your warning level just wait about 6 seconds and the pointer will stop flashing and retain that point as your new warning level. If you pass the point you wanted to set the level at-just keep going and once it reaches the end of the scale it will begin to come back."
HTH
Trending Topics
#10
Hi i have just the saga boost gauge on my wagon and setting goes
press once quickly,needle goes to previous alarm setting.to set,press and hold button in, needle will automatically reset to zero and move up when it reaches new alarm setting release the button,press setting button again quickly and new value is set. should be the same for their gauges.hope this helps you out mate
press once quickly,needle goes to previous alarm setting.to set,press and hold button in, needle will automatically reset to zero and move up when it reaches new alarm setting release the button,press setting button again quickly and new value is set. should be the same for their gauges.hope this helps you out mate
#12
Just out of interest,what do you have your oil pressure gauge set to??
Mine is the same as yours
Gonna do this for mine tomorrow so hopefully it will work for me as well
Many thanks
Bernie
Mine is the same as yours
Gonna do this for mine tomorrow so hopefully it will work for me as well
Many thanks
Bernie
#16
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jan 2010
Location: London
Posts: 1,179
Likes: 0
Received 0 Likes
on
0 Posts
Nedster I have done the steps you instructed, works properly, however when I turn the car off and turn it back on it seems to be resetting itself back to normal.
Please advice further thanks...
Neel
Please advice further thanks...
Neel
#17
Hi Neel,thought we were gettin somewhere,are you setting with engine at idle needs to be set with ignition on only i think, also have you got the calibration **** might be best to start again.Other than that setting is as i said earlier i know mine went a bit weird once and i recallibrated it and reset and been fine since.if you still have problems may be worth contacting autodials.co.uk they could help as said earlier.
nedster
nedster
#18
Scooby Regular
Thread Starter
iTrader: (18)
Join Date: Jan 2010
Location: London
Posts: 1,179
Likes: 0
Received 0 Likes
on
0 Posts
Yeah it sets but does not save, I have set it with engine running and also with ignition on, makes no difference . I have already reset it, makes no difference. This is getting very annoying now.
Thanks
Thanks
#19
Scooby Regular
iTrader: (11)
If it's setting OK but not saving, most likely you've got the +12v input wired to an ignition-switched feed instead of a permanent feed. I don't think many of these gauges will save otherwise (even a lot of decent Jap-branded CD players don't save radio presets and so on without continuous power, so not really surprising).
Thread
Thread Starter
Forum
Replies
Last Post