Which cambelt tensioner to fit?
#1
Scooby Regular
Thread Starter
Join Date: Nov 2000
Location: 32 cylinders and many cats
Posts: 18,658
Likes: 0
Received 1 Like
on
1 Post
http://www.scoobynet.co.uk/bbs/threa...=179486&Page=7
As requested new thread.
Opinions please on whether the fit a new Phase II tensioner or to fit a Phase I which is thought by some/many to be more robust.
What do I need to fit a Phase I tensioner to the Phase II engine?
A 30000 mile old Phase II tensioner reused nearly cost me the demise of a pukka engine rebuild
One aftermarket specialist routinely fits a new cambelt tensioner with a belt change, all the rest I've quizzed do not.
Was I just unlucky?
The tensioner appeared to work fine when fitted, and had been tensioned slowly in a vice over 15 mins. The service manual recommends 3 minutes. Some people just sqaush them
As requested new thread.
Opinions please on whether the fit a new Phase II tensioner or to fit a Phase I which is thought by some/many to be more robust.
What do I need to fit a Phase I tensioner to the Phase II engine?
A 30000 mile old Phase II tensioner reused nearly cost me the demise of a pukka engine rebuild
One aftermarket specialist routinely fits a new cambelt tensioner with a belt change, all the rest I've quizzed do not.
Was I just unlucky?
The tensioner appeared to work fine when fitted, and had been tensioned slowly in a vice over 15 mins. The service manual recommends 3 minutes. Some people just sqaush them
#4
the block doesn't affect it. The tensioner sits on a subframe casting that bolts onto the left block half. to change you would need the casting, the tensioner, and if not the roller itself, certainly the little off centre pivot shaft it sits on, and of course the tensioner.
I would guess the original belt is now toast.
Paul
I would guess the original belt is now toast.
Paul
#5
if it is the tensioner that works vertical this type should not be pushed back in a vice over any period of time as it knackers it. it needs to be pressed back in the way it operates i.e vertical there is a bullitin from subaru about this as it causes it to lose tension the only one that can be pushed back in a vice is the horizontal type.
#7
Scooby Regular
iTrader: (1)
Join Date: Mar 2002
Location: Norn Iron
Posts: 2,786
Likes: 0
Received 0 Likes
on
0 Posts
The belt is different ????????
I sent David pics of both. Im sure he can post them.
To swap, you do need all the bits. Ally subframe, roller/pivot bolt, and tensioner.
If it was me, I would be quite happy using sec hand parts. As Ive said, the tensioners dont normally give any bother. My own car is still using the original one, and has had several belts, and 130k+ miles.
Its the same type of tensioner used on a few Jap cars, a long thin hydraulic plunger.
[Edited by ustolemyname??stevieturbo - 10/07/2003 22:00:21]
[Edited by ustolemyname??stevieturbo - 10/07/2003 22:07:48]
I sent David pics of both. Im sure he can post them.
To swap, you do need all the bits. Ally subframe, roller/pivot bolt, and tensioner.
If it was me, I would be quite happy using sec hand parts. As Ive said, the tensioners dont normally give any bother. My own car is still using the original one, and has had several belts, and 130k+ miles.
Its the same type of tensioner used on a few Jap cars, a long thin hydraulic plunger.
[Edited by ustolemyname??stevieturbo - 10/07/2003 22:00:21]
[Edited by ustolemyname??stevieturbo - 10/07/2003 22:07:48]
Trending Topics
#8
I did mess about with this a little, my own my00 v6 did suffer a slipped belt when useing the engine for hard braking. I have used the latest type tensioner with the extra idler wheel to the right and used the early shorter belt, my snap on belt tension kit gave a reading of max tension. There was no belt wine as you get with a belt that is over tight, has done 6000 miles and put to the test so fare all is well. Not saying this is the only way to go, just that it has worked well for me.
Steve.
Steve.
#9
Scooby Regular
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
steve if thats the snap on belt tension measuring kit i think it is I got a refund for mine recently as it was poo.. snap on man agreed..
Lets sort this as there are pistons, valves, money at stake.... Im inclined to say I agree with steve.. but he is paying if he's wrong
Lets sort this as there are pistons, valves, money at stake.... Im inclined to say I agree with steve.. but he is paying if he's wrong
#11
All the tensioners i have here including the latest type, all have the same part number. To avoid confusion these are the second design of tensioner not the type stevie speaks of.
David the kit i have has about 5 or 6 parts to it cost about £250, i only use it as a double check when there is any dout. Does this sound like the same kit?.
Steve.
David the kit i have has about 5 or 6 parts to it cost about £250, i only use it as a double check when there is any dout. Does this sound like the same kit?.
Steve.
#12
Hi John
Just had a 45k service on MY99 and pointed out to the dealer there was a noise from the tensioner, sounded just like your sound file only not as pronounced, they replaced the belt but not the tensioner, 4 weeks later this had to be replaced due to me still complianing, they confirmed the tensioner, however noise was still present but reduced. Now car is coing back in to have the tensioner replaced again 3 weeks after the other one. This had been requested by regional service manager after i had a word with IM. He will then come and have a listen to the problem.
All i can say that it is definitely the tensioner. Just wondering now if they have changed the design or had a bad batch. Its in next Wednesday for its second in 7 weeks.
Just had a 45k service on MY99 and pointed out to the dealer there was a noise from the tensioner, sounded just like your sound file only not as pronounced, they replaced the belt but not the tensioner, 4 weeks later this had to be replaced due to me still complianing, they confirmed the tensioner, however noise was still present but reduced. Now car is coing back in to have the tensioner replaced again 3 weeks after the other one. This had been requested by regional service manager after i had a word with IM. He will then come and have a listen to the problem.
All i can say that it is definitely the tensioner. Just wondering now if they have changed the design or had a bad batch. Its in next Wednesday for its second in 7 weeks.
#13
there is a bullitin from subaru about this as it causes it to lose tension the only one that can be pushed back in a vice is the horizontal type.
, is this a fairly recent discovery? .
I compressed the tensioner as we have always done, in a bench vice, just much slower to avoid any risk.usually it takes approx 2min but I actually took 10-12 this time thinking it was safer with such an expensive engine , I also did it the 2min way for an accident damaged MY99 a few years ago, which has since done 30000+miles and quite a few track days, guess I was lucky.
knew I should not have got involved with the fitting of old tensioners,idlers and release bearings with this high spec engine!
[Edited by T-uk - 7/13/2003 1:41:56 PM]
, is this a fairly recent discovery? .
I compressed the tensioner as we have always done, in a bench vice, just much slower to avoid any risk.usually it takes approx 2min but I actually took 10-12 this time thinking it was safer with such an expensive engine , I also did it the 2min way for an accident damaged MY99 a few years ago, which has since done 30000+miles and quite a few track days, guess I was lucky.
knew I should not have got involved with the fitting of old tensioners,idlers and release bearings with this high spec engine!
[Edited by T-uk - 7/13/2003 1:41:56 PM]
#17
it's only the later type where it's all built in that needs to be done in a press the old thin cylinder type (the better one in my opinion) that can be done in a vice
#18
Scooby Regular
iTrader: (1)
Join Date: Mar 2002
Location: Norn Iron
Posts: 2,786
Likes: 0
Received 0 Likes
on
0 Posts
Generally with timing belts, once they have been used, you are not supposed to re-tension them. ( ie. use old ones )
In saying that, I have re-used mine once or twice with no problems.
Better to be safe though, if you dont know the milage on the belt, or if perhaps there is 20k+ on it...just replace it.
In saying that, I have re-used mine once or twice with no problems.
Better to be safe though, if you dont know the milage on the belt, or if perhaps there is 20k+ on it...just replace it.
#19
I was told by a knowledgeable person that the old tensioner is definitely more reliable. The new one is more prone to failure often because the method of compressing it is not done properly and causes problems.
Les
Les
#20
Scooby Regular
Join Date: Oct 2001
Location: Bish,Bash,Bosham!
Posts: 2,204
Likes: 0
Received 0 Likes
on
0 Posts
Quick question. I mentioned this in another post but hopefully someone here can clear this up...
What type of tensioner should be fitted to a UK MY97?
Had it replaced last year (leaking) by Subaru dealer - 194+VAT.
Cambelt was also done as it was due a change (45k).
It's now noisy and going in next week to be replaced (again).
Opinions?
Cheers,
Jay
What type of tensioner should be fitted to a UK MY97?
Had it replaced last year (leaking) by Subaru dealer - 194+VAT.
Cambelt was also done as it was due a change (45k).
It's now noisy and going in next week to be replaced (again).
Opinions?
Cheers,
Jay
#22
Scooby Regular
Join Date: Oct 2001
Location: Bish,Bash,Bosham!
Posts: 2,204
Likes: 0
Received 0 Likes
on
0 Posts
Cheers Stevie, it just didn't make sense to me. So I take it there's no way an early tensioner should be £194+VAT? Maybe dealers 'consider' the later type to be an 'improved' part... Either way I will be having words next week!
Cheers again, Jay.
Cheers again, Jay.
#25
John
Just had my second timing belt tensioner fitted this morning, 2 in seven weeks, see earlier thread to MY99. However it still makes the same noise as the last one, this had been fitted at a main dealer and they confirm that it is this, that is still making the noise.
Does anyone know for sure which tensioner was fitted to the MY99.
They also said that this is the latest design, the old ones never had this problem.
Can any good engine builders confirm this.
Now awaiting inspection from I.M.
Think i would fit the old type.
Just had my second timing belt tensioner fitted this morning, 2 in seven weeks, see earlier thread to MY99. However it still makes the same noise as the last one, this had been fitted at a main dealer and they confirm that it is this, that is still making the noise.
Does anyone know for sure which tensioner was fitted to the MY99.
They also said that this is the latest design, the old ones never had this problem.
Can any good engine builders confirm this.
Now awaiting inspection from I.M.
Think i would fit the old type.
#26
Scooby Regular
Join Date: Oct 2001
Location: Bish,Bash,Bosham!
Posts: 2,204
Likes: 0
Received 0 Likes
on
0 Posts
Eprom - see above ^
It *appears* anything from at least MY97 onwards can have the later tensioner fitted, but I am yet to see a definitive answer i.e. MY96 onwards had new tensioner... Maybe it varies but looks like my MY97 had the newer style (ar$e [img]images/smilies/mad.gif[/img]) therefore I think it is safe to say the MY99 will certainly have the new tensioner.
J
It *appears* anything from at least MY97 onwards can have the later tensioner fitted, but I am yet to see a definitive answer i.e. MY96 onwards had new tensioner... Maybe it varies but looks like my MY97 had the newer style (ar$e [img]images/smilies/mad.gif[/img]) therefore I think it is safe to say the MY99 will certainly have the new tensioner.
J
Thread
Thread Starter
Forum
Replies
Last Post
JonMc
Subaru Parts
22
06 February 2016 09:50 PM
MH-Racing
Subaru Parts
18
18 October 2015 04:49 PM
Danny0608
Subaru
6
27 September 2015 02:16 PM
Danny0608
Subaru Parts
0
12 September 2015 02:59 PM