Prodriverules 'candy' makeover
#1
Prodriverules 'candy' makeover
Another project for us to get our teeth into,this time it's a bit different as this one's going 'candy apple red'!
It's going to be the darker wine shade of candy so it won't be to over bearing in it's colour,should hopefully look quite special once finished.
As with any classic impreza it's got the usual rusting in the rear arches and a few dinks here and there,but I must say the shell overall is in good condition.
The fun has started with removal of the exterior trims/door handles etc and prep has begun,rusted arche area's have been cut out and new steel is to be welded in.
I'm sure the owner will be along soon to claim right to the vehicle
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
It's going to be the darker wine shade of candy so it won't be to over bearing in it's colour,should hopefully look quite special once finished.
As with any classic impreza it's got the usual rusting in the rear arches and a few dinks here and there,but I must say the shell overall is in good condition.
The fun has started with removal of the exterior trims/door handles etc and prep has begun,rusted arche area's have been cut out and new steel is to be welded in.
I'm sure the owner will be along soon to claim right to the vehicle
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Trending Topics
#8
Scooby Regular
Join Date: Aug 2004
Location: north wales
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
Before The car got dropped at Ryan's I had the following done.
NEW Block
NEW 92.50 mm Cosworth pistons and NPR piston rings
NEW APi Steel rods with 9000 rpm big end bolts
NEW crank
NEW ACL race bearings on mains and big ends
Compression set to 8.4:1 using NEW .7mm steel laminate STi head gaskets.
Rebuilt Modified APi oil pump
Fully overhauled used STi Vers 2 RA heads with small ‘top hat’ shims, RA Cams and valves
NEW cam belt
NEW Sti gaskets and seals throughout.
NEW standard Subaru head bolts.
NEW Tufnol heatproof Inlet manifold spacers
NEW cold air kit
AFP Td05 18G
550CC Injectors
Currently running on Autronic ecu but soon will be Alcatek
Sti 6 gearbox and rear diff
Gearbox overhauled ref poor synchro 5th gear.
Fitted NEW 5th gear synchro hub
NEW 5th gear synchro ring
Perfect used 5th gear
2 NEW x drop gear bearings
NEW Gasket and seal kit
75w40 gear oil fitted
Superflex suspension parts as follows;
Front anti lift kit
Front wishbone inner bushes
Rack mounts
Rear radius arm inner and outer bushes
Lower rear upright bushes
Anti tramp kit
Eibach / whiteline camber adjusting bolts.
Should make a nice road car when finished
NEW Block
NEW 92.50 mm Cosworth pistons and NPR piston rings
NEW APi Steel rods with 9000 rpm big end bolts
NEW crank
NEW ACL race bearings on mains and big ends
Compression set to 8.4:1 using NEW .7mm steel laminate STi head gaskets.
Rebuilt Modified APi oil pump
Fully overhauled used STi Vers 2 RA heads with small ‘top hat’ shims, RA Cams and valves
NEW cam belt
NEW Sti gaskets and seals throughout.
NEW standard Subaru head bolts.
NEW Tufnol heatproof Inlet manifold spacers
NEW cold air kit
AFP Td05 18G
550CC Injectors
Currently running on Autronic ecu but soon will be Alcatek
Sti 6 gearbox and rear diff
Gearbox overhauled ref poor synchro 5th gear.
Fitted NEW 5th gear synchro hub
NEW 5th gear synchro ring
Perfect used 5th gear
2 NEW x drop gear bearings
NEW Gasket and seal kit
75w40 gear oil fitted
Superflex suspension parts as follows;
Front anti lift kit
Front wishbone inner bushes
Rack mounts
Rear radius arm inner and outer bushes
Lower rear upright bushes
Anti tramp kit
Eibach / whiteline camber adjusting bolts.
Should make a nice road car when finished
#12
Scooby Regular
Join Date: Aug 2004
Location: north wales
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
#17
As I had bare metal/filler on show and I haven't had time this week to fabricate pieces for the rear arches as it's quite involved with filler after I decided to get the shell into high build primer ready for block flatting.
Once the rear arches are done and in primer it will be time to remove the front bumper/doors/boot and bonnet so we can get the back sides painted plus door shuts.
At this point we will re-install the doors/boot/bonnet,remove front/rear glass and shoot the candy on the car as one par bumper,doors handles/side skirts and spolier so we get the best match throughout the car.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Once the rear arches are done and in primer it will be time to remove the front bumper/doors/boot and bonnet so we can get the back sides painted plus door shuts.
At this point we will re-install the doors/boot/bonnet,remove front/rear glass and shoot the candy on the car as one par bumper,doors handles/side skirts and spolier so we get the best match throughout the car.
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#26
Scooby Regular
iTrader: (100)
Join Date: Oct 2008
Location: Planet Earth
Posts: 13,684
Likes: 0
Received 0 Likes
on
0 Posts
I saw this car today and it looks even better in sunlight, let me just host the pics and I will show you all how good a job this really is.
If the owner of the car wants them in their full unstripped out, pre Photobucket glory then just drop me a PM with your email address on it and I will send the HDR versions through.
If the owner of the car wants them in their full unstripped out, pre Photobucket glory then just drop me a PM with your email address on it and I will send the HDR versions through.