blob, main beam manual height adjustment?
#1
Scooby Regular
Thread Starter
iTrader: (20)
Join Date: Apr 2009
Location: London
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
blob, main beam manual height adjustment?
Hi all,
My driver side main beam went over the weekend.
I replaced both side with a set of Philips Diamond Vision.
Now my passenger side beam is higher than my driver side.
I tried the interior height adjustment and only move both up and down.
Searched quite a few places and they all say there is some kind of a screw on the lamp to adjust.
Where is this screw located?
OR can anyone show me a pic of this or circle an image of where is it?
Many thanks.
J.
My driver side main beam went over the weekend.
I replaced both side with a set of Philips Diamond Vision.
Now my passenger side beam is higher than my driver side.
I tried the interior height adjustment and only move both up and down.
Searched quite a few places and they all say there is some kind of a screw on the lamp to adjust.
Where is this screw located?
OR can anyone show me a pic of this or circle an image of where is it?
Many thanks.
J.
#2
Scooby Regular
iTrader: (2)
WAIT!
Replacing bulbs should have NO effect on the height settings of headlamps.
It's more likely that either the bulb isn't seated properly, or that you altered the position of the headlight slightly when replacing the bulb.
Did you have to remove the headlight to do it?
My bet, however, would be a badly seated bulb
Replacing bulbs should have NO effect on the height settings of headlamps.
It's more likely that either the bulb isn't seated properly, or that you altered the position of the headlight slightly when replacing the bulb.
Did you have to remove the headlight to do it?
My bet, however, would be a badly seated bulb
#3
Scooby Regular
Thread Starter
iTrader: (20)
Join Date: Apr 2009
Location: London
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
I didn't take the whole light out to change the blub. But did remote the breather pipes and the battery to get behind it all.
The H1 bulb have 2 small studs which have to line up in order to clamp it down with the bracket. Therefore it is sitting correctly, as thats the 1st thing I checked...
Any ideas about this manual adjuster?
The H1 bulb have 2 small studs which have to line up in order to clamp it down with the bracket. Therefore it is sitting correctly, as thats the 1st thing I checked...
Any ideas about this manual adjuster?
#4
Scooby Regular
iTrader: (2)
If the bulb is seated properly, how much is the beam out now?
Sorry, I have a classic, so can't help with the adjuster.
They are USUALLY a hexagon headed screw sitting vertically, if the lights have electrical adjustment, they will be part of that. On mine they also have a cross-point hole in the top to allow socket, or screwdriver adjustment.
Once you find it, stand the car in front of the gaage door, or a wall, and test which way the light goes as you turn the screw clockwise.
Then you'll know when you take it somewhere dark to adjust it
Sorry, I have a classic, so can't help with the adjuster.
They are USUALLY a hexagon headed screw sitting vertically, if the lights have electrical adjustment, they will be part of that. On mine they also have a cross-point hole in the top to allow socket, or screwdriver adjustment.
Once you find it, stand the car in front of the gaage door, or a wall, and test which way the light goes as you turn the screw clockwise.
Then you'll know when you take it somewhere dark to adjust it
#6
Scooby Regular
Thread Starter
iTrader: (20)
Join Date: Apr 2009
Location: London
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
Ok, took the entire lamp out so I might as well de-tango them at the same time.
I cant find any screws which adjust the height of the main beam.
However, I took some pics of the rear of the lamp.
There is this square ting on the bottom right corner, but how do I adjust it:
I cant find any screws which adjust the height of the main beam.
However, I took some pics of the rear of the lamp.
There is this square ting on the bottom right corner, but how do I adjust it:
Trending Topics
#8
Scooby Regular
Thread Starter
iTrader: (20)
Join Date: Apr 2009
Location: London
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
No I haven't remove it, I tried to turn the white thing and it will go round and round and round... luckily I remembered how many turns, so I turn it the other way (back to how it was).
Dont tell me that I have to turn it, stick the lamp back to the car, put the lights on, remove the lamp to adjust and so on?
Dont tell me that I have to turn it, stick the lamp back to the car, put the lights on, remove the lamp to adjust and so on?
#11
Scooby Regular
iTrader: (2)
Looks like those lights are like my Xantia ones: levelling is for BOTH main and dip at the same time.
What does the dip beam look like? See, what worries me is that if you raise driver's side M/B, you ALSO raise that side dip, and it will be naff......and dazzling.
What MAKE of bulb did you put in?
What does the dip beam look like? See, what worries me is that if you raise driver's side M/B, you ALSO raise that side dip, and it will be naff......and dazzling.
What MAKE of bulb did you put in?
#14
Scooby Regular
Thread Starter
iTrader: (20)
Join Date: Apr 2009
Location: London
Posts: 415
Likes: 0
Received 0 Likes
on
0 Posts
But the switch does move the beam up and down.
Because the beam is not level, I am worrying that it will fail the MOT...
Thread
Thread Starter
Forum
Replies
Last Post
Sam Witwicky
Engine Management and ECU Remapping
17
13 November 2015 10:49 AM
Pro-Line Motorsport
Car Parts For Sale
2
29 September 2015 07:36 PM