FAO all defi users
#1
Scooby Regular
Thread Starter
Join Date: Oct 2012
Location: southport
Posts: 673
Likes: 0
Received 0 Likes
on
0 Posts
FAO all defi users
So I've had the gauges installed today and I've run into a couple of problems. Firstly the gauges don't Zero - well the Oli pressure an temp one don't when there is no ignition on - the oil pressure just wants to sit at 4 ! The oil pressure is reading high but I'm not sure if its because its not starting at zero. The temp is showing the last read temp. Also on a steady drive the boost needle is flickering- I've attached a vid to show you what I mean !
Any help will be appreciated !
http://i950.photobucket.com/albums/ad346/johninspain/E3E221B2-47A0-4DBD-8807-9BF93C859885-234-0000001DF1982AA2_zps1f89e26c.mp4
http://i950.photobucket.com/albums/ad346/johninspain/B3A931A6-C929-4DC3-838C-73C8CA492C33-234-0000001C2705F80E_zpsb414cfd1.mp4
Any help will be appreciated !
http://i950.photobucket.com/albums/ad346/johninspain/E3E221B2-47A0-4DBD-8807-9BF93C859885-234-0000001DF1982AA2_zps1f89e26c.mp4
http://i950.photobucket.com/albums/ad346/johninspain/B3A931A6-C929-4DC3-838C-73C8CA492C33-234-0000001C2705F80E_zpsb414cfd1.mp4
Last edited by blackpoolrock; 25 April 2013 at 08:49 PM.
#2
Scooby Regular
iTrader: (2)
Check first the wiring to the control unit. It should be as follows:
RED: PERMANENT live.
ORANGE: SWITCHED (from ign) live.
WHITE: LIGHTING live.
Black: EARTH, a good one.
Next check that each gauge sender is plugged into it's correct socket at the control box.
Next check that the daisy chain is from gauge to gauge and then, finally, to the control box, socket "A" if you have Defi Link, and socket "B" if you have defi BF gauges.
Come back to us when you have checked that all is well with the wiring.
RED: PERMANENT live.
ORANGE: SWITCHED (from ign) live.
WHITE: LIGHTING live.
Black: EARTH, a good one.
Next check that each gauge sender is plugged into it's correct socket at the control box.
Next check that the daisy chain is from gauge to gauge and then, finally, to the control box, socket "A" if you have Defi Link, and socket "B" if you have defi BF gauges.
Come back to us when you have checked that all is well with the wiring.
#3
Scooby Regular
Thread Starter
Join Date: Oct 2012
Location: southport
Posts: 673
Likes: 0
Received 0 Likes
on
0 Posts
I didn't do a permutation live ! Would this make all the difference ? Surly it wouldn't make any difference when the ignition is on and the car running ? What about the boost being like it is ?
#5
Scooby Senior
iTrader: (3)
Join Date: Jun 2006
Location: Slowly rebuilding the kit of bits into a car...
Posts: 14,333
Likes: 0
Received 0 Likes
on
0 Posts
If you had them wired correctly you could have recorded the memory playback, not risked "live action" on the road.
dunx
P.S. With no ignition on, they should be off !
dunx
P.S. With no ignition on, they should be off !
#7
Scooby Regular
Thread Starter
Join Date: Oct 2012
Location: southport
Posts: 673
Likes: 0
Received 0 Likes
on
0 Posts
It's in to have them sorted tomoz but with no ignition on even now they should read zero ! What's going on do you think ? What's with the boost ?
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
shorty87
Full Cars Breaking For Spares
19
22 December 2015 11:59 AM
Pro-Line Motorsport
Car Parts For Sale
2
29 September 2015 07:36 PM