Notices
General Technical
Sponsored by:
Sponsored by: CARiD

Idle / Stalling

Thread Tools
 
Search this Thread
 
Old Oct 11, 2010 | 10:02 PM
  #1  
Kevin_STI's Avatar
Kevin_STI
Thread Starter
Scooby Regular
iTrader: (57)
 
Joined: Jul 2008
Posts: 794
Likes: 1
From: Leeds
Default Idle / Stalling

Hi my STI 8 stalls when dropping down through the gears.

Example, coming off the motorway down the slip road from 70 - 0mph dropping down gears it stalls when I drop the clutch between 3rd - 2nd gear or putting it in neutral just before it comes to a stand still?

Only does it now and again

Any ideas at all peeps?

Cheers

Kev
Reply
Old Oct 11, 2010 | 10:40 PM
  #2  
Lewak's Avatar
Lewak
Scooby Regular
iTrader: (1)
 
Joined: Feb 2008
Posts: 238
Likes: 0
From: Earth
Default

Check your pipes for any splits would be a good start i think. What mods have you got?
Reply
Old Oct 11, 2010 | 11:02 PM
  #3  
Kevin_STI's Avatar
Kevin_STI
Thread Starter
Scooby Regular
iTrader: (57)
 
Joined: Jul 2008
Posts: 794
Likes: 1
From: Leeds
Default

Originally Posted by Lewak
Check your pipes for any splits would be a good start i think. What mods have you got?
Thanks for the info I have just had my engine rebuild however it did do it before the build.

Have decat pipe, DV, Induction kit thats it really. I will check the main pipes however checking all of them for a tiny split wud be difficult

I'm getting it mapped soon, will the mapper be able to find the leak...?

Kev

Last edited by Kevin_STI; Oct 11, 2010 at 11:04 PM.
Reply
Old Oct 11, 2010 | 11:44 PM
  #4  
patmo498's Avatar
patmo498
Scooby Regular
iTrader: (1)
 
Joined: Aug 2009
Posts: 80
Likes: 0
From: brecon
Default

check your maff mate. could be a air flow problem
Reply
Old Oct 12, 2010 | 12:00 AM
  #5  
chrisdicko's Avatar
chrisdicko
Scooby Regular
iTrader: (21)
 
Joined: Oct 2008
Posts: 3,016
Likes: 0
From: Whitby, North Yorkshire
Default

Is the dump valve working correctly? Do you have a standard one to try? If not you could remove the DV that is on at the moment, block the hole in the intercooler, and put a bolt in the Vac pipe and try that. If it still does it, obviously it isnt the DV and you can rule that out....
Reply
Old Oct 12, 2010 | 07:55 AM
  #6  
Stevesbluewrx's Avatar
Stevesbluewrx
Scooby Regular
iTrader: (4)
 
Joined: Aug 2005
Posts: 3,662
Likes: 0
From: Also known as The Gimp
Default

Sounds more like a leak in the intercooler pipe or cooler itself.

Wouldn't rule out the maf or ICV. What does the car do when starting from cold? How does it idle then?


Steve
Reply
Old Oct 12, 2010 | 07:16 PM
  #7  
Kevin_STI's Avatar
Kevin_STI
Thread Starter
Scooby Regular
iTrader: (57)
 
Joined: Jul 2008
Posts: 794
Likes: 1
From: Leeds
Default

Originally Posted by patmo498
check your maff mate. could be a air flow problem
Cheers mate I'll check it and mate sure it's clean etc.

Originally Posted by chrisdicko
Is the dump valve working correctly? Do you have a standard one to try? If not you could remove the DV that is on at the moment, block the hole in the intercooler, and put a bolt in the Vac pipe and try that. If it still does it, obviously it isnt the DV and you can rule that out....
It's a HKS SSQV and it works fine dumps everytime etc but I will try the above and see what happens?

Originally Posted by Stevesbluewrx
Sounds more like a leak in the intercooler pipe or cooler itself.

Wouldn't rule out the maf or ICV. What does the car do when starting from cold? How does it idle then?


Steve
What is a ICV? The car is fine from cold, it's only when slowing down from 50+ mph - 0 the revs drop down under 1K and then it stalls.... Only does it now and again, once today....

I have been told it mite be the idle control valve?

Thanks for the replies
Reply
Old Oct 12, 2010 | 07:43 PM
  #8  
Lewak's Avatar
Lewak
Scooby Regular
iTrader: (1)
 
Joined: Feb 2008
Posts: 238
Likes: 0
From: Earth
Default

ICV is the Idel control Valve mate. Normaly these can be just cleaned out and then replaced.

Cheers

Dave
Reply
Old Oct 12, 2010 | 11:09 PM
  #9  
Kevin_STI's Avatar
Kevin_STI
Thread Starter
Scooby Regular
iTrader: (57)
 
Joined: Jul 2008
Posts: 794
Likes: 1
From: Leeds
Default

Originally Posted by Lewak
ICV is the Idel control Valve mate. Normaly these can be just cleaned out and then replaced.

Cheers

Dave
Cheers
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
Dec 28, 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
Nov 18, 2015 07:03 AM
supshon
General Technical
2
Oct 3, 2015 08:06 PM
the shreksta
General Technical
9
Sep 20, 2015 09:21 AM
blackandz
General Technical
0
Sep 12, 2015 07:01 PM




All times are GMT +1. The time now is 05:59 AM.