engine management light advise needed
#1
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Jan 2010
Location: streatham
Posts: 100
Likes: 0
Received 0 Likes
on
0 Posts
engine management light advise needed
hello people,
i have a 2001 bugeye wrx
the issue i have is that the engine management light is on, i have plugged it into a diagnostics machine and the fault came back as a misfire on cylinder 2. i changed the plugs and cleared all the fault codes..... happy days
after about 20mins of driving the light came back on. i then got a new coilpack and fitted it to what i was told was cylinder 2 (standing at the front of the car the right hand side of the engine closest to me) i cleared the coded again and the same thing happened
the car seems to be running ok (idles fine, i noticed at motorway speeds the car seemed to hold back a little, not a lot but i noticed it) i dont like the idear of just leaving this and im now stuck on what to do
any help or advise would be great
i have a 2001 bugeye wrx
the issue i have is that the engine management light is on, i have plugged it into a diagnostics machine and the fault came back as a misfire on cylinder 2. i changed the plugs and cleared all the fault codes..... happy days
after about 20mins of driving the light came back on. i then got a new coilpack and fitted it to what i was told was cylinder 2 (standing at the front of the car the right hand side of the engine closest to me) i cleared the coded again and the same thing happened
the car seems to be running ok (idles fine, i noticed at motorway speeds the car seemed to hold back a little, not a lot but i noticed it) i dont like the idear of just leaving this and im now stuck on what to do
any help or advise would be great
#4
Scooby Regular
iTrader: (6)
Join Date: Jan 2009
Location: on sunny ibiza ocean beach
Posts: 5,594
Likes: 0
Received 0 Likes
on
0 Posts
how many fault codes were there po nos bugeyes are prone for dodgey sensors which can be unplugged and cleaned then the codes will go it has happend to me quick clean off sensor plugs and sensor not had a problem since touch wood
Trending Topics
#8
Scooby Regular
Join Date: Nov 2007
Location: solihull
Posts: 940
Likes: 0
Received 0 Likes
on
0 Posts
i had 0304 missfire on 4 for ages,changed plugs,swapped coil over and still come on,car ran ok, so in the end i had it turned off in the map that simon aka jgm had done.i have cut that story down by loads and it really p1ssed me off !!! must have reset the ecu about 10 times and also had nps switch changed as that can throw up a missfire code,that may be your fault you know as yours is holding back on motorway.mine is my 02 sti bugeye,and since had it turned off in map its been ace! i know what its like tho not knowing if its a major fault or not.good luck.
#9
I have the same problem with my 01 bugeye WRX cleared the codes changed the plugs, the light still on but it is running fine, what mods have you done as I have put it down to de-catting and re-mapping. I am having another upgrade next month, turbo, injectors etc and map and the tuner says the ECU is missing a reading so throws a fault even though no actual problem he told me they can solder in a resister to make the light go off?
#11
Scooby Regular
iTrader: (78)
Misfire codes can sometime be related to the NPS (Neutral Position Switch). This is a common fault and happens regular on higher power cars due to the torque in the gearbox. The parts in around £40 delivered and takes around 5mins over a pit to fit on WRX cars, the STI is trickier I believe.
Hope this thread helps
https://www.scoobynet.com/general-te...es-grrrrr.html
Rob
Hope this thread helps
https://www.scoobynet.com/general-te...es-grrrrr.html
Rob
#13
Scooby Regular
iTrader: (78)
#14
Former Sponsor
Join Date: Dec 2005
Location: 10.68 QT mile in 2007 2.33 Type R ** Current 2002 Spec C 2.33 Track prepped.
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
hello people,
i have a 2001 bugeye wrx
the issue i have is that the engine management light is on, i have plugged it into a diagnostics machine and the fault came back as a misfire on cylinder 2. i changed the plugs and cleared all the fault codes..... happy days
after about 20mins of driving the light came back on. i then got a new coilpack and fitted it to what i was told was cylinder 2 (standing at the front of the car the right hand side of the engine closest to me) i cleared the coded again and the same thing happened
the car seems to be running ok (idles fine, i noticed at motorway speeds the car seemed to hold back a little, not a lot but i noticed it) i dont like the idear of just leaving this and im now stuck on what to do
any help or advise would be great
i have a 2001 bugeye wrx
the issue i have is that the engine management light is on, i have plugged it into a diagnostics machine and the fault came back as a misfire on cylinder 2. i changed the plugs and cleared all the fault codes..... happy days
after about 20mins of driving the light came back on. i then got a new coilpack and fitted it to what i was told was cylinder 2 (standing at the front of the car the right hand side of the engine closest to me) i cleared the coded again and the same thing happened
the car seems to be running ok (idles fine, i noticed at motorway speeds the car seemed to hold back a little, not a lot but i noticed it) i dont like the idear of just leaving this and im now stuck on what to do
any help or advise would be great
Thread
Thread Starter
Forum
Replies
Last Post
robbie1988
Wanted
2
13 September 2015 09:25 AM
Scooby-Doo 2
Wheels And Tyres For Sale
1
09 September 2015 06:51 PM