how do i get 300bhp from my r reg turbo 2000
#1
Scooby Regular
Thread Starter
Join Date: Aug 2009
Location: doncaster
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
how do i get 300bhp from my r reg turbo 2000
hi everybody i have recently purchaced an r reg impreza turbo 2000 and am wanting more power i would like 300bhp to start with as i plan a large engine build in the future.your advice would be mutch apreciated
#2
#5
Buy the best you can afford of everything otherwise you will buy twice on many items as power increases.
Examples:
Large Front Mounted Inter Cooler
ECU
Closed Deck Block (if you intend proper power) 500+
Trending Topics
#8
my uk 97 runs 331bhp
i have full decat,vf34 turbo,bigger injectors,fmic,and a simtek
speak to martin at alan jeffery
i have full decat,vf34 turbo,bigger injectors,fmic,and a simtek
speak to martin at alan jeffery
Last edited by stewart1397; 01 August 2009 at 10:18 PM.
#11
Scooby Regular
I would recommend the Apexi Power FC ECU. It's ideal for what you want(300bhp) and there's no need to go with the simtek on a MY98 UK Turbo because the MAF sensor doesn't have the same issues as the 99/00 cars.
Edited to say - My Apexi was £930 fitted and mapped by Andy Forrest, which is pretty much the going rate among all the good mappers.
Edited to say - My Apexi was £930 fitted and mapped by Andy Forrest, which is pretty much the going rate among all the good mappers.
Last edited by GlesgaKiss; 02 August 2009 at 12:51 AM.
#12
911 C4 pilot
iTrader: (7)
Join Date: Jan 2007
Location: In an Air Cooled Porsche
Posts: 3,578
Likes: 0
Received 0 Likes
on
0 Posts
Get the simtek, it deletes the MAF & IMHO is a better ECU than the Apexi (I've used both) and the Simtek has antilag & launch control.
Give Enginetuner a call & speak to Martyn
Give Enginetuner a call & speak to Martyn
#14
Scooby Regular
Thread Starter
Join Date: Aug 2009
Location: doncaster
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
think ime gonna go we simtek management to start with.my plans are a front mount cooler,full 3"system from turbo bk,td05 turbo and c wat that makes then ile be saving up for a 400plus motor
#18
Scooby Regular
iTrader: (3)
Join Date: Aug 2000
Location: 1600cc's of twin scroll fun :)
Posts: 25,565
Likes: 0
Received 2 Likes
on
2 Posts
400BHP on a uk classic will cost you a fortune, 300 will be expensive enough, forget going 2.5 unless you have cash for a gearbox and clutch upgrade as the extra torque will kill both, your probably looking at 1k for the simtek mapped/fitted, a few hundred for the turbo, you WILL need to upgrade the brakes on your car to something seriously better, the subaru 4 pots are the cheapest option at around 250 for a good set, and then you will have to upgrade the discs and pads.
So your probably looking at 2.5k for a decent 300bhp build, but I would get a car health check before carrying out any work to start with to see if you have any other problems.
Oh and your car doesnt have a version no matter what people say, its totally confusing as only STI's have versions (classic ones only)
Tony
So your probably looking at 2.5k for a decent 300bhp build, but I would get a car health check before carrying out any work to start with to see if you have any other problems.
Oh and your car doesnt have a version no matter what people say, its totally confusing as only STI's have versions (classic ones only)
Tony
#19
Scooby Regular
I'm sure the Simtek is more expensive and doesn't have knock correction? Why would you go for that over the Apexi when you're only looking for 300bhp and you don't need anti-lag?
Can you imagine running anti-lag and launch control on what is basically a near standard Turbo 2000? Disaster waiting to happen.
Can you imagine running anti-lag and launch control on what is basically a near standard Turbo 2000? Disaster waiting to happen.
#21
Scooby Regular
iTrader: (13)
Apexi
No active ign. timing retard/adv.
Just a couple of knock warings (Commander numerical level reading and CEL flash threshold limit).
Also has CEL flash warnings for "Air Flow voltage" and "Inj. duty cycle" threshold setting.
Simtek
No ign. retard/adv.
Just a CEL flash for knock level threshold..... BUT I believe Simtek are working on a firmware upgrade to include active ign. retard/adv.
No active ign. timing retard/adv.
Just a couple of knock warings (Commander numerical level reading and CEL flash threshold limit).
Also has CEL flash warnings for "Air Flow voltage" and "Inj. duty cycle" threshold setting.
Simtek
No ign. retard/adv.
Just a CEL flash for knock level threshold..... BUT I believe Simtek are working on a firmware upgrade to include active ign. retard/adv.
Last edited by joz8968; 02 August 2009 at 01:21 PM.
#22
Scooby Regular
iTrader: (13)
As said, I think Simtek is overkill when compared to the money required to be spent on the other supporting mods. I'd seriously look for a cheapish 2nd hand Apexi PFC too. Plus, it's more than capable...
Also, the MY97/98 MAFs are much more robust than the MY99/00 ones. Plus you can constantly monitor its output voltage on the Apexi Commander anyway (as well as set up that CEL flash feature if you want) - so no worries there...
Also, the MY97/98 MAFs are much more robust than the MY99/00 ones. Plus you can constantly monitor its output voltage on the Apexi Commander anyway (as well as set up that CEL flash feature if you want) - so no worries there...
Thread
Thread Starter
Forum
Replies
Last Post