Fueling question with Link
24 November 2001, 12:01 AM
#1
Scooby Regular
Thread Starter
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Has anyone running a link put 480cc injectors on a YM93 WRX?
If you have what general changes did you have to make with the map (cold start, master fuel etc) ?
Cheers
Pete
If you have what general changes did you have to make with the map (cold start, master fuel etc) ?
Cheers
Pete
24 November 2001, 10:27 AM
#2
Scooby Regular
Join Date: Dec 2000
Posts: 2,912
Likes: 0
Received 0 Likes
on
0 Posts
What size did you have before?
I do think decreasing master fuel by one click at a time should be enough.
Be careful and do it slow....remember to check fuelling on boost so you're not running lean.
/J
I do think decreasing master fuel by one click at a time should be enough.
Be careful and do it slow....remember to check fuelling on boost so you're not running lean.
/J
24 November 2001, 01:44 PM
#3
Scooby Regular
Thread Starter
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Jerry,
It had the WRX grey 380cc injectors.
They were topping out at 5700 RPM (108% injection), so wasn`t getting the benifit of the top end. I`m not sure about what kind of nick the lambda sensor is in (60,000 miles) so changing that as well to get some true readings on the knocklink.
Cheers
Pete
It had the WRX grey 380cc injectors.
They were topping out at 5700 RPM (108% injection), so wasn`t getting the benifit of the top end. I`m not sure about what kind of nick the lambda sensor is in (60,000 miles) so changing that as well to get some true readings on the knocklink.
Cheers
Pete
24 November 2001, 03:09 PM
#4
Scooby Regular
Join Date: Dec 2000
Posts: 2,912
Likes: 0
Received 0 Likes
on
0 Posts
You must surely mean the lambdalink mate... 
I'm running 12:1 throughout the rev range on row 6 (from 3500 rpm where me VF24 really kicks in), and I have had *zilch* problems with det.
With the crappy TD04 there was another story altogether...that ****** gave me headaches at ZI635...
Good luck mate!
/J
I'm running 12:1 throughout the rev range on row 6 (from 3500 rpm where me VF24 really kicks in), and I have had *zilch* problems with det.
With the crappy TD04 there was another story altogether...that ****** gave me headaches at ZI635...
Good luck mate!
/J
24 November 2001, 05:32 PM
#5
Scooby Regular
Thread Starter
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Jerry,
Well spotted m8. U passed that test
Wasn`t awake when i posted earlier (jus outta sack syndrome).
Maybe you could help with this 1 though?
My new sensor has a signal + and a signal - connector.
Which cable do i connect the signal - to on the lambdalink?
The black (signal +) goes to the White (signal) but cant figure the grey
Cheers m8
Pete
Well spotted m8. U passed that test
Wasn`t awake when i posted earlier (jus outta sack syndrome).
Maybe you could help with this 1 though?
My new sensor has a signal + and a signal - connector.
Which cable do i connect the signal - to on the lambdalink?
The black (signal +) goes to the White (signal) but cant figure the grey
Cheers m8
Pete
Thread
Thread Starter
Forum
Replies
Last Post
hedgecutter
General Technical
3
25 September 2015 02:35 PM