what ecu is this
#1
what ecu is this
i bought my MY99 impreza turbo from a guy who claims its been chipped. i thought i would have a look under the passenger footwell and the ecu has certainly been messed with but can anyone tell me what ECU/piggy back/remap this is?
#2
Scooby Regular
Join Date: Jan 2003
Location: 535D M-Sport Touring
Posts: 3,190
Likes: 0
Received 0 Likes
on
0 Posts
From the outside it looks like a standard AE802, as fitted to MY00, apart from the writing on the ECU. Can't see anything wired onto the PCB, such as a piggy back chip, but I'm no expert.
It may have been remapped with ECUTEK. If this is the case it's not chipped as such, the maps are reprogrammed using the ECUTEK software.
Have you got a boost gauge and if so is it boosting to 1.1 bar. At standard ECU will boost to 0.9 bar.
It may have been remapped with ECUTEK. If this is the case it's not chipped as such, the maps are reprogrammed using the ECUTEK software.
Have you got a boost gauge and if so is it boosting to 1.1 bar. At standard ECU will boost to 0.9 bar.
#5
Scooby Regular
Join Date: Nov 2003
Location: where the wild roses grow
Posts: 5,122
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by zakesm
anybody else know?
there is no JECS/UNISIA branding in the ecu board?
is it completely changed?
If it has been remapped, it's been done via EcuTeK, and in this case there's obviously no way to tell just by looking at the thing.
At end of day the pen markings on the can could be complete bull****. The only real way you have to tell is to fit it in a car equipped with a known standard 802 and drive. If it is indeed a TeK2 or TeK3, it should feel quicker than the vanilla ECU, and should, if the scribbling on the can is accurate, do noticeably more to your boost gauge. As Graz says, standard boost target on these cars is 0.9 bar - plus or minus any gauge inaccuracy.
There is certainly no evidence of a fuel cut defender, piggy back chip or similar device on the ECU board itself, or on the bit of loom you have shown in the picture. Have you checked the wiring round the MAP sensor to see if there's anything unusual soldered in round there?
Last edited by greasemonkey; 10 June 2004 at 12:05 AM.
#6
so the car has either been ecutek'd or its standard. one curious thing is that when i check the error codes on the car by connecting the plugs under the driver dash, there is no response, the CEL light just stays on continously. is this a symptom of ecutek?
greasemonkey - where is the MAP sensor so i can check the wiring around there.
why is the arrow with the word 'LECI' pointing to one of the wiring loom connector things? what does this mean?
one more comment - when i took off the ecu cover, the four tiny screws were covered in untampered white pain (they had not been opened since the paint was applied). is this done at factory or perhaps by a remapper?
thanks 4 the help guys
zak
greasemonkey - where is the MAP sensor so i can check the wiring around there.
why is the arrow with the word 'LECI' pointing to one of the wiring loom connector things? what does this mean?
one more comment - when i took off the ecu cover, the four tiny screws were covered in untampered white pain (they had not been opened since the paint was applied). is this done at factory or perhaps by a remapper?
thanks 4 the help guys
zak
Last edited by zakesm; 11 June 2004 at 04:56 AM.
Trending Topics
#9
Scooby Regular
Join Date: Nov 2003
Location: where the wild roses grow
Posts: 5,122
Likes: 0
Received 0 Likes
on
0 Posts
Lol, I think we covered that one before Jay.
Zak: The MAP sensor is the upper of the three gadgets on a plate bolted onto the front of the right hand strut tower, so look for anything untoward clipped onto the wiring in that area.
Zak: The MAP sensor is the upper of the three gadgets on a plate bolted onto the front of the right hand strut tower, so look for anything untoward clipped onto the wiring in that area.
#10
thanks greasy - i will check that out.
does an ecuteked impreza turbo not show error codes like normal by connecting the plugs under the dash - the CEL light just stays on on my car when i do this, does not flash or go off. (it is not on during driving).
does an ecuteked impreza turbo not show error codes like normal by connecting the plugs under the dash - the CEL light just stays on on my car when i do this, does not flash or go off. (it is not on during driving).
#11
ok guys i got a boost gauge - and the car boosts as follows (in bar);
idle : -0.5
1st gear : 0.7
2nd/3rd :0.9
4th/5th :0.95-1.0
peak values obv.
so with the pictures of my ecu in mind - has the car been ecutekd or not?
motec is also popular here in kenya (for rally cars) could mine have been motec'd?
oh yeah all the above boost figures are running on kenyan 'super' fuel : 93 octane leaded!
zak
idle : -0.5
1st gear : 0.7
2nd/3rd :0.9
4th/5th :0.95-1.0
peak values obv.
so with the pictures of my ecu in mind - has the car been ecutekd or not?
motec is also popular here in kenya (for rally cars) could mine have been motec'd?
oh yeah all the above boost figures are running on kenyan 'super' fuel : 93 octane leaded!
zak
#12
Scooby Regular
Join Date: Nov 2003
Location: where the wild roses grow
Posts: 5,122
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by zakesm
does an ecuteked impreza turbo not show error codes like normal by connecting the plugs under the dash
See other thread for answer to your boost question.
Thread
Thread Starter
Forum
Replies
Last Post