just picked up one of these to do what its doing :)
08 May 2010, 06:58 PM
#1
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Dec 2002
Location: just about to jump off the wardrobe...
Posts: 4,878
Likes: 0
Received 0 Likes
on
0 Posts
just picked up one of these to do what its doing :)
http://www.youtube.com/watch?v=mWemc...eature=related
Just picked up a shabby looking e30 325i 2 door 1989
underneath is covered in surface rust we are going to attack it next week with grinder welder and a big tub of underseal.
sort out the brakes and add a hydralic handbrake
strip out the interior and add a roll cage and pair of bucket seats
and give it a coat of paint
will add some pics i took before my batterys run out lol.
Just picked up a shabby looking e30 325i 2 door 1989
underneath is covered in surface rust we are going to attack it next week with grinder welder and a big tub of underseal.
sort out the brakes and add a hydralic handbrake
strip out the interior and add a roll cage and pair of bucket seats
and give it a coat of paint
will add some pics i took before my batterys run out lol.
08 May 2010, 06:59 PM
#2
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Dec 2002
Location: just about to jump off the wardrobe...
Posts: 4,878
Likes: 0
Received 0 Likes
on
0 Posts
forgot to say i wont be anywere near as good as that good
but it shouldnt be so hard i was **** hot at karting 15 years ago
but it shouldnt be so hard i was **** hot at karting 15 years ago
especially stripped out!!
09 May 2010, 10:24 AM
#5
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Dec 2002
Location: just about to jump off the wardrobe...
Posts: 4,878
Likes: 0
Received 0 Likes
on
0 Posts
i had it sideways around the car park outside the garage yesterday
cant wait for it to be looking good
were going into banger racing when it starts next month too down marshfield
my mates letting us have his massive iveco panel van and were going to kit it out as a
tow/support/camper van to make life easyer for us
cant wait for it to be looking good
were going into banger racing when it starts next month too down marshfield
my mates letting us have his massive iveco panel van and were going to kit it out as a
tow/support/camper van to make life easyer for us
Trending Topics
10 May 2010, 05:08 PM
#8
Scooby Regular
Join Date: May 2006
Location: Secretly saving for another Blobeye STI. Crystal Grey. Widetrack
Posts: 1,985
Likes: 0
Received 0 Likes
on
0 Posts
I once had a metallic black left hooker on an E plate. 325i. Lovely car.
Built back in the day when there weren't many about.
I reckon a mint one is still one of the nicest looking cars built.
I saw a bright metallic blue one the other day by crumlin. Lovely.
Built back in the day when there weren't many about.
I reckon a mint one is still one of the nicest looking cars built.
I saw a bright metallic blue one the other day by crumlin. Lovely.
10 May 2010, 11:41 PM
#11
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Dec 2002
Location: just about to jump off the wardrobe...
Posts: 4,878
Likes: 0
Received 0 Likes
on
0 Posts
yeah hopefully do a bit of trackdaying with it but going to put a hydralic handbrake on it for drifting too. (look at the back wheel against the arch )
spent the day on it today,
striped out all the interior apart from the dash.
going to use my wrx seats when i fit my new ones to my car
cut out the spare wheel carryer rust and welded in a new section,
cut out the rust in the battery tray area in the boot and welded in new sections.
cut out the rust along the drivers side sills and front wing and welded in new plates.
cut out the rust in the front d/s under bumper section and welded in a new plate.
the front corner under the wing was worse than 1st thought and after cutting most of the rust out the floor where the throttle pedal mounts was falling out so had to weld in a new floor section and have to re-mount the thottle peddal
)spent the day on it today,
striped out all the interior apart from the dash.
going to use my wrx seats when i fit my new ones to my car
cut out the spare wheel carryer rust and welded in a new section,
cut out the rust in the battery tray area in the boot and welded in new sections.
cut out the rust along the drivers side sills and front wing and welded in new plates.
cut out the rust in the front d/s under bumper section and welded in a new plate.
the front corner under the wing was worse than 1st thought and after cutting most of the rust out the floor where the throttle pedal mounts was falling out so had to weld in a new floor section and have to re-mount the thottle peddal
11 May 2010, 11:43 PM
#13
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Dec 2002
Location: just about to jump off the wardrobe...
Posts: 4,878
Likes: 0
Received 0 Likes
on
0 Posts
bit more welding done today and took some more bits off,
took of the plastic trim and filling it in
cut away the wheel arches so the wheels wont rub at all.
and flated a bit of the paintwork down
took of the plastic trim and filling it in
cut away the wheel arches so the wheels wont rub at all.
and flated a bit of the paintwork down
04 June 2010, 05:42 PM
#17
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Dec 2002
Location: just about to jump off the wardrobe...
Posts: 4,878
Likes: 0
Received 0 Likes
on
0 Posts
we had a bit of silver and a bit of red left in the cupboard so we put it all in a tin and thats what we come out with 
Thread
Thread Starter
Forum
Replies
Last Post