adzer

iTrader: (13)

ok guys i have an alarm that i need to get fitted before my car gets broke into!!! after alot of searching i have found out what wires are for what, can anyone maybe help comfirm where i wire them upto?? i have a fair idea about some but not all of them.

1 - Blue - Interior light pin switches (neg)
2 - Blue/Red - Boot switch (neg)
3 - Green/Black - Low current programable output
4 - Green/Red - As above
5 - Black - Earth
6 - Black - Earth
7 - Orange - Ignition sense
8 - Red - 3a 12v
9 - Pink - Central locking (Configurable)
10 - Blue/White - As Above
11 - Black - Immobiliser circuit 1
12 - Black - Immobiliser circuit 1
13 - Black - Immobiliser circuit 2
14 - Black - Immobiliser circuit 2
15 - Red/Yellow - Indicator supply (15a)
16 - Yellow - Indicator output
17 - Yellow - Indicator output
18 - Green/Orange - Accessory output (neg during trigger)
19 - Green/White - Central locking (Configurable)
20 - Pink/Black - Central locking (Configurable)

Car Security Expert

I would advise that you take it to a professional installer to have it installed. If your not 100% sure of what your doing you could cause some serious and expensive damage to your car..

Is it worth the risk?

adzer

iTrader: (13)

the car is a run around and not willing to pay someone to do something i can do and have done before.

its just the way that its worded thats confusing me.

1- goes to door light switch?
2- boot light switch (if fitted with one)
3- unknown
4- unknown
5- chassis ground
6- chassis ground
7- ignition wire (but which? switched or perm live)
8- 12v supply
9- central locking module??? (lock or unlock???)
10- central locking module??? (lock ore unlock???)
11- fuel pump
12- fuel pump
13- starter motor
14- starter motor
15- 12v supply????
16- left indicator power wire???
17- right indicator power wire???
18- unknown???
19- central locking module??? (lock or unlock???)
20- central locking module??? (lock or unlock???)

that is what i think these wires are for but due to the lack of description on the list i recieved i'm not 100% sure tho.

i am about to add a central locking motor kit to my car aswell so i can have remote central locking.

scoobynewbie72

iTrader: (1)

3 is for a Rad fan if it runs after the ignition is off
7 is when the ignition is on, so it thinks the engine is running,
18 will need to be grounded, Its to pass thru spot lights etc i believe,

Car Security Expert

Going by the descriptions in post 1 none of those are correct.

3 is a channel output wire as is 18. 7 will be an ignition "live when cranking" wire.



What make/model of alarm is it your trying to fit?

adzer

iTrader: (13)

it is a sigma m series alarm.

Car Security Expert

1 - door pin switch
2 - boot light switch
3 -
4 -
5 - Black - Earth
6 - Black - Earth
7 - ignition live while cranking
8 - 12v
9 - Pink - Central locking (Configurable)
10 - Blue/White - As Above
11 - Immobiliser circuit 1
12 - Immobiliser circuit 1
13 - Immobiliser circuit 2
14 - Immobiliser circuit 2
15 - 12v
16 - Indicator output
17 - Indicator output
18 -
19 - Green/White - Central locking (Configurable)
20 - Pink/Black - Central locking (Configurable)

adzer

iTrader: (13)

ok mate that clears that one up

only question i have now is how to wire it up to the central locking??

alarm has 4 wires for the central locking, but i only need two.
1 for lock and 1 for unlock

a take it any of the pair will do?

Car Security Expert

you will need to work out how the locking works on the alarm. If you use a multimeter it should help you sort it out.

adzer

iTrader: (13)

yeah good plan

thanks bud