jimbobs

my mate has his old P1 ecu which he says I can have, he recons it will pug straight in and run fine with the mods I have and should give me some good gains!? is this correct? ive read a few threads some say yes some say no?

chrispy200+

iTrader: (2)

I'd say don't do it, what turbo etc do you have and mods?

jimbobs

just standard TD04, 3" bellmouth decat with 3" straight through, pipercross induction, n a sti tmic with uprated y pipe!

PADDYHOEY

iTrader: (24)

You'd need the key from the p1. As the keys are chip keys !

chrispy200+

iTrader: (2)

Sure the p1 has a vf28 like the type r, I personally wouldn't bother, you'd be better of getting yours mapped, much safer

jimbobs

im not going to argue with you mate you probably know ten times more than me, but are you 100% sure on that? he recons it was on his my00 and was just plug n play??
thanks for the reply

jimbobs

mmmm, what do you mean by safer mate? could id seriously damage my engine?
cheers for the reply

bradm27scooby

iTrader: (3)

Check out my mines ecu and td05 could suit you better

jimbobs

what you mean mate? check what out were?

bradm27scooby

iTrader: (3)

In for sale section I'm breaking a wagon with loads of mods the mines ecu I have might suit you better , u will need 440's td05 full decat and air filter and it will raise ur boost and will give u around 300bhp

mnem1c

iTrader: (4)

Even tho the P1 is classed as a UK car, Prodrive did not map or change the ecu for the uk. The P1 ecu is a standard JDM v5 sti ecu.

I'll place a bet with you that if you plug this ecu in, your car will go bang!

mnem1c

iTrader: (4)

How will this be better, your trying to sell him a jap ecu, with an aggressive jap map.

bradm27scooby

iTrader: (3)

It's on a uk car with these mods to match it and it's running spot on mate has been for ages, so i was saying this would be better with these mods than just putting an ecu straight onto a standard car

mnem1c

iTrader: (4)

Are you sure its a UK car, have never seen Mines on uk ecu's. Mines are a Jap tuning company and map their ecu's to run on 100ron+

CREWJ

You will probably end up with less power as the map was designed for a different engine.

Jolly Green Monster

iTrader: (4)

There is no ecu immobiliser on 99/00 classics but you will need to alter three pins at the ecu for it to start.

The map it totally wrong and you will blow the engine up and gain nothing powerwise in the process.

scoobyboy1

iTrader: (16)

^^^^^^^^^^^^^^^^^^^

If this guy says it wont work and will blow your engine up, I would value his opinion over anyone else's on here when it comes to ecu's!!


Just get your ecu mapped, will cost you around £500 and mapped to your car, and tell your mate you will have his P1 ecu and then stick it on e-bay and get some money for it!!!

bradm27scooby

iTrader: (3)

^^^^^

*matthewturb2000*

iTrader: (11)

What's the code on front of p1 edu, just I was told when I bought my car the ad said "p1ecu fitted" I've checked and being a ppp car it has the correct sp sti ecu , my 1999 uk2000

Gear Head

iTrader: (2)

What would you hope to gain by swapping this ecu? If its a blown engine......go for it!

In all seriousness, think about it. It is mapped for a different engine and turbo combo. What do you think will happen?

jimbobs

obviously was hoping more power lol, but im new to all this hence the reason I asked on here before plugging it in! ive read loads of posts were people have said, prodrive ecu fitted! n they have si ular mods to me!, !

jimbobs

cheers guys im listening, I wownt fit it , bit gutted tbh as I haven't got a spare £500 at the mo! I will have to wait for after crimbo and get mine mapped!

alcazar

iTrader: (2)

Worth the wait. JGM is correct, (he usually is), and the cost of a blown engine is FAR FAR more than £500, so rest secure that your engine will be OK.

Gear Head

iTrader: (2)

If you have the spare £500, get a proper remap.

jimbobs

what do you mean a proper re map? as appose to what mate?

Aaron1978

iTrader: (12)

With the mods you listed in post #3, has it already been remapped?

Hol

iTrader: (1)

A mapper once told me that the P1 map is a STI map with better knock sensitivity to cope with the low Ron fuel over here. A quick fix for Subaru.

As a result, he always started with a baseline P1 map when he remapped STI 5 & 6's.



What the OP's mate really wants to find is an ECU from a 99/00 Uk PPP car, as with just an STI equivalent exhaust, and intercooler piping they made 250ibs of torque. Almost the same as a P1.

Rare to find for sale, but probably in loads of breakers. Pink label and says STI on it.

Jolly Green Monster

iTrader: (4)

P1 and sti map identical. The only mod to the p1 ecu related was a speed delimiter wired into the harness.
P1 was never safe for uk fuel hence so many blew up.

jimbobs

im not sure mate is there a way to tell?

jimbobs

https://www.scoobynet.com/engine-man...drive-ecu.html

so what is this all about?