280bhp P1 ecu on my uk2000 what will happen?
my mate has his old P1 ecu which he says I can have, he recons it will pug straight in and run fine with the mods I have and should give me some good gains!? is this correct? ive read a few threads some say yes some say no?
|
I'd say don't do it, what turbo etc do you have and mods?
|
just standard TD04, 3" bellmouth decat with 3" straight through, pipercross induction, n a sti tmic with uprated y pipe!
|
You'd need the key from the p1. As the keys are chip keys !
|
Sure the p1 has a vf28 like the type r, I personally wouldn't bother, you'd be better of getting yours mapped, much safer
|
Originally Posted by PADDYHOEY
(Post 11226944)
You'd need the key from the p1. As the keys are chip keys !
thanks for the reply:thumb: |
Originally Posted by chrispy200+
(Post 11226946)
Sure the p1 has a vf28 like the type r, I personally wouldn't bother, you'd be better of getting yours mapped, much safer
cheers for the reply:thumb: |
Check out my mines ecu and td05 could suit you better
|
Originally Posted by bradm27scooby
(Post 11226965)
Check out my mines ecu and td05 could suit you better
|
In for sale section I'm breaking a wagon with loads of mods the mines ecu I have might suit you better , u will need 440's td05 full decat and air filter and it will raise ur boost and will give u around 300bhp
|
Even tho the P1 is classed as a UK car, Prodrive did not map or change the ecu for the uk. The P1 ecu is a standard JDM v5 sti ecu.
I'll place a bet with you that if you plug this ecu in, your car will go bang! |
Originally Posted by bradm27scooby
(Post 11226971)
In for sale section I'm breaking a wagon with loads of mods the mines ecu I have might suit you better , u will need 440's td05 full decat and air filter and it will raise ur boost and will give u around 300bhp
|
It's on a uk car with these mods to match it and it's running spot on mate has been for ages, so i was saying this would be better with these mods than just putting an ecu straight onto a standard car
|
Originally Posted by bradm27scooby
(Post 11226975)
It's on a uk car with these mods to match it and it's running spot on mate has been for ages, so i was saying this would be better with these mods than just putting an ecu straight onto a standard car
|
:facepalm:
You will probably end up with less power as the map was designed for a different engine. |
There is no ecu immobiliser on 99/00 classics but you will need to alter three pins at the ecu for it to start.
The map it totally wrong and you will blow the engine up and gain nothing powerwise in the process. |
^^^^^^^^^^^^^^^^^^^
If this guy says it wont work and will blow your engine up, I would value his opinion over anyone else's on here when it comes to ecu's!!:thumb: Just get your ecu mapped, will cost you around £500 and mapped to your car, and tell your mate you will have his P1 ecu and then stick it on e-bay and get some money for it!!!:D |
Originally Posted by scoobyboy1
(Post 11227085)
^^^^^^^^^^^^^^^^^^^
If this guy says it wont work and will blow your engine up, I would value his opinion over anyone else's on here when it comes to ecu's!!:thumb: Just get your ecu mapped, will cost you around £500 and mapped to your car, and tell your mate you will have his P1 ecu and then stick it on e-bay and get some money for it!!!:D |
What's the code on front of p1 edu, just I was told when I bought my car the ad said "p1ecu fitted" I've checked and being a ppp car it has the correct sp sti ecu , my 1999 uk2000
|
What would you hope to gain by swapping this ecu? If its a blown engine......go for it!
In all seriousness, think about it. It is mapped for a different engine and turbo combo. What do you think will happen? |
Originally Posted by Gear Head
(Post 11227119)
What would you hope to gain by swapping this ecu? If its a blown engine......go for it!
In all seriousness, think about it. It is mapped for a different engine and turbo combo. What do you think will happen? |
:wall:cheers guys im listening, I wownt fit it , bit gutted tbh as I haven't got a spare £500 at the mo! I will have to wait for after crimbo and get mine mapped!
|
Originally Posted by jimbobs
(Post 11227132)
:wall:cheers guys im listening, I wownt fit it , bit gutted tbh as I haven't got a spare £500 at the mo! I will have to wait for after crimbo and get mine mapped!
|
Originally Posted by jimbobs
(Post 11227132)
:wall:cheers guys im listening, I wownt fit it , bit gutted tbh as I haven't got a spare £500 at the mo! I will have to wait for after crimbo and get mine mapped!
|
Originally Posted by Gear Head
(Post 11227270)
If you have the spare £500, get a proper remap. :thumb:
|
With the mods you listed in post #3, has it already been remapped?
|
A mapper once told me that the P1 map is a STI map with better knock sensitivity to cope with the low Ron fuel over here. A quick fix for Subaru.
As a result, he always started with a baseline P1 map when he remapped STI 5 & 6's. What the OP's mate really wants to find is an ECU from a 99/00 Uk PPP car, as with just an STI equivalent exhaust, and intercooler piping they made 250ibs of torque. Almost the same as a P1. Rare to find for sale, but probably in loads of breakers. Pink label and says STI on it. |
P1 and sti map identical. The only mod to the p1 ecu related was a speed delimiter wired into the harness.
P1 was never safe for uk fuel hence so many blew up. |
Originally Posted by Aaron1978
(Post 11227481)
With the mods you listed in post #3, has it already been remapped?
im not sure mate is there a way to tell? |
|
All times are GMT +1. The time now is 06:25 PM. |
© 2024 MH Sub I, LLC dba Internet Brands