Dent Removal
#2
Scooby Senior
Join Date: Jul 2001
Location: Radiator Springs
Posts: 14,810
Likes: 0
Received 0 Likes
on
0 Posts
Dentmaster are always good, prolly look in the yellow pages for your local one, no idea of price, it tends to vary
Bob
ps, it's a fecking lot harder to do it than it looks
Bob
ps, it's a fecking lot harder to do it than it looks
#4
I used Dent Wizard, same setup as DM. They usually charge £80 per panel (so £75 is about the going rate) and I needed 3 out of 4 doors doing but they cut me a deal and did the lot for £100.
#5
Scooby Regular
iTrader: (1)
Join Date: Sep 2001
Location: Just north of Harlow on the border
Posts: 1,713
Likes: 0
Received 0 Likes
on
0 Posts
Try these
http://www.dentdevils.co.uk/
Someone on here used them if I recall and reckoned they did a good job
I have not yet (fingers crossed) needed there service
http://www.dentdevils.co.uk/
Someone on here used them if I recall and reckoned they did a good job
I have not yet (fingers crossed) needed there service
#6
We have used Dent-Fixa (Richard Voce)very reasonable price, certainly not £75 per panel.
Beechdale in Nottingham also use him - took the Scoob there when it was a week old (Oops!!) Also took a dent out of our other car for 1/4 the price of the dealer (nissan). Very tidy job an all!
I also know that a number of other people on this BBS have used his services in the past.
If you would like his phone no. email me off line, I have his card in front of me now.
BB
Beechdale in Nottingham also use him - took the Scoob there when it was a week old (Oops!!) Also took a dent out of our other car for 1/4 the price of the dealer (nissan). Very tidy job an all!
I also know that a number of other people on this BBS have used his services in the past.
If you would like his phone no. email me off line, I have his card in front of me now.
BB
Trending Topics
#8
Scooby Regular
Join Date: Mar 2001
Location: Birmingham
Posts: 15,507
Likes: 0
Received 0 Likes
on
0 Posts
Clare if you want to drive to brum sunday i'll get your door done for around £20, Wont take any longer than an hour, Mail me
Pete, they use a selection of steal rods, with an assortment of different shaped heads on them and prize the dent out from the inside of the panel.
I have even seen them use a small hammer on the outside of the dent / panel to get it flush again
BUT it looks the dogs when they are finished
Pete, they use a selection of steal rods, with an assortment of different shaped heads on them and prize the dent out from the inside of the panel.
I have even seen them use a small hammer on the outside of the dent / panel to get it flush again
BUT it looks the dogs when they are finished
#10
Hi.
I have a dent/crease in the pasenger side rear wing, just above the wheel arch, behind rear door. Can this be removed? As ita a crease rather than dent I wondered if it would be permannent?
I have a dent/crease in the pasenger side rear wing, just above the wheel arch, behind rear door. Can this be removed? As ita a crease rather than dent I wondered if it would be permannent?
#12
Scooby Regular
Join Date: Mar 2001
Location: Birmingham
Posts: 15,507
Likes: 0
Received 0 Likes
on
0 Posts
NP, IF its a horizontal crease its the worst type to get out, might not be able to get it out completely but it can be made to look a lot better.
Needs to be seen really mate
Needs to be seen really mate
#15
Scooby Regular
Join Date: Jun 2002
Location: From the land of dings and dents
Posts: 4,556
Likes: 0
Received 0 Likes
on
0 Posts
Nuclear Pond,
I have had all sorts of dents and a particularly bad horizontal crease taken out of the top of my drivers side front wing.(step ladders fell on it whilst in the garage!). So don't despair these guys can work miracles. Pity your not in the north west, Bolton area, I know this top guy who would do it as a cash in hand jobby.
Good luck Rasher..
I have had all sorts of dents and a particularly bad horizontal crease taken out of the top of my drivers side front wing.(step ladders fell on it whilst in the garage!). So don't despair these guys can work miracles. Pity your not in the north west, Bolton area, I know this top guy who would do it as a cash in hand jobby.
Good luck Rasher..
#17
A guy looked at it today form ChipsAway. Said that because he cant get to the inside, via wheelarch, he would need to drill a small hole in the panel inside the rear door, just below the U shaped catch, to ghet the rods in. I was a bit worried about the drilling bit. Is this OK? He sais it would be sealed afterwards.
Thread
Thread Starter
Forum
Replies
Last Post