oli_p

iTrader: (4)

Right have got the clocks in at the mo, have cut C9 to stop the buzzing although this was C9 on original cluster, C2 on 07 pin layout with plug turn 180 degrees to fit.

Im now wanting to sort out the handbrake light, diff temp light and the ABS light.

A2 needs to be earth for handbrake light to work correctly, but I have no pin going to A2, so I did A2 from the original cluster on loom, which just made fuel tank show as empty, so does anyone know the colour wire at all, or what pin location it is for the handbrake on the loom side??

Also I know about the relay needed for the ABS, have everything for that but it says to use B3 for relay, but again I have no pin. Do I take do pin
B3 from wiring loom side or the cluster side?? or again anyone know what colour the wire should be??

B4 for diff temp light, have no pin in either side 07 pin layout or factory loom layout so would need a pin from somewhere and fit that myself, which won't be hard when I found out where to get pin from.

Anyone have any info for the handbrake light wire and abs wire would be helpful, also if anyone has the pin layout for 03 wrx clocks may help

Thanks

Oli

oli_p

iTrader: (4)

think what im mainly confused about, is should all the above wires be done from the cluster layout or original cluster layout?? just don't want to short anything or bugger the clocks

tubbytommy

iTrader: (20)

Lol

oli_p

iTrader: (4)

??

fawor

iTrader: (3)

Tape them all,you dont need to see abs light on start up and diff.
handbrake will be nice to see when applied but its only in case you forget about it when driving.
could live withouth.

oli_p

iTrader: (4)

nah would prefer to do it properly, don't like doing half jobs, its possible, but im just unsure if im taking things from the loom side or the new cluster pin layout, ill try sort the abs light tomorrow

tubbytommy

iTrader: (20)

bodge it why not lol

oli_p

iTrader: (4)

well ive sorted the abs light earlier, diff temp will be sorted when I get another plug to remove the pin. Just the handbrake light now, so anyone that maybe able to help please do
earthing A2 seems to just make my fuel tank read empty/empty light flash

tubbytommy

iTrader: (20)

what relay did you use for the abs light??
ill have a look at my clocks later in the week i forget what i did to get the handbrake working.

oli_p

iTrader: (4)

just used a 5 pin relay from maplins.

85 any ignition live
86 cut wire from loom
30 earth
87a cut wire from clocks

tubbytommy

iTrader: (20)

ahh just wondered i got an ebay one and it didnt work, got a link for the relay?

oli_p

iTrader: (4)

http://www.maplin.co.uk/40a-spno-and...ve-relay-37526

Thats what I used, pin 87 isn't used either, read on one thread that it didn't work for someone as they connected it to 87 instead of 87a

tubbytommy

iTrader: (20)

ill take a look. ta

oli_p

iTrader: (4)

main thing I was unsure about for handbrake light, was that thread I got the info from, chap that provided the info was helping someone with a 02 wrx, which means A2 would be C2 on clocks after 03, I guess I could try earth C2 instead see if that works, but fairly sure C plug just provides power to the cluster?
Have read in another thread, that someone used wire B19 which is linked the handbrake light, but this was a US site so could be different with our clocks

oli_p

iTrader: (4)

No probs

tubbytommy

iTrader: (20)

there is a lot of differences between models and years, i had to take a look at the wiring diagrams online for mine.

you need to ground out the rear diff light on your model i think.

oli_p

iTrader: (4)

yes have been looking all over for wiring diagrams and which pin etc is used for which warning light etc but no luck.

Yes B4 seems correct, but my plug has no pin in it, so waiting for a plug from another member to remove pins from that, so will add my own pin to B4 then ground it

oli_p

iTrader: (4)

diff light now sorted, just handbrake light, no joy with earthing pin b19 though

tubbytommy

iTrader: (20)

there is 3 on this link i take it it is the 12v one?

oli_p

iTrader: (4)

N01AW is the one I used the top one, although one at very bottom N00AW is the 12v one, had the top one as it was the only 5 pin one they had in the store. sure either will work fine though

fawor

iTrader: (3)

oli_p

iTrader: (4)

think I may of sorted the handbrake light aswell, need to earth pin A1 I believe not A2. Been having a mess with the other pins on the A plug aswell which seem to make different diff lights come on, so going to see if I can get the C.diff light to work as it should aswell

FredW

iTrader: (9)

This may be of some use to you guys. I fitted a 06 Hawkeye Spec D (defi style clock) into my 03 STi and have a DCCD box out of a RB320 using a DCCDPro controller. PLUG 'A', and I assume you shaved the top and bottom left hand lugs off the 14 pin plug so that it would fit into the 16 pin Hawkeye clock socket, mapping is shown below. Pins 1 & 8 in the 16 pin socket are not used so you will see why you found the fuel gauge on A3 if you applied an earth to A2. If its of any use I have an amended wiring diag that I can scan and email to you or PM me if you need any other info.

oli_p

iTrader: (4)

cheers Fred, think I may of sussed out the handbrake light now, im tempted to now find away to get the C.diff light to turn off, im wondering if I maybe earth the auto pin, if that would turn the Cdiff light off maybe

Mark10sti

iTrader: (2)

Just stumbled on this ready to weigh in but you have worked it all out except the light I haven't managed to extinguish which is the c dif light, interested to see IC this is possible