Why won't my Viper d600.1 amp run with 1 ohm load?
#1
Scooby Regular
Thread Starter
Join Date: Sep 2002
Location: Nottingham - HEY scumbag,leave my scoob alone!!!
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Just rewired my sub so that it is a 1 ohm load, the sub is a single rockford 2215 15" with 2 ohm voice coils (DVC) , it is on a Viper d600.1 amp but the amp keeps shutting down when the volume is up, I thought these amps where supposed to be 1 ohm stable.
Am i putting to much power through this sub, is that why the amp keeps quitting? Or has the amp gone dodgy?
I running the sub on just one of the v/c's at the mo, i know that i should'nt , but it runs with no problems that way. I've tried the sub set at four ohm but it seems to lack power
Any thought on this please
BigRed
Am i putting to much power through this sub, is that why the amp keeps quitting? Or has the amp gone dodgy?
I running the sub on just one of the v/c's at the mo, i know that i should'nt , but it runs with no problems that way. I've tried the sub set at four ohm but it seems to lack power
Any thought on this please
BigRed
#2
Scooby Regular
If i'm right the 2215 is 1000w RMS!
My pheonix gold amp (500w rms) was doing the same thing when i tried to power my 2212 subs (500w rms)
I upgraded my battery and used a power cap, that seemed to work for a bit until my amp fried.
I was told that my subs require a lot of power to drive them.
I suspect you would need a much more powerfull amp like the viper 1200.1 or RF 1000bd
My pheonix gold amp (500w rms) was doing the same thing when i tried to power my 2212 subs (500w rms)
I upgraded my battery and used a power cap, that seemed to work for a bit until my amp fried.
I was told that my subs require a lot of power to drive them.
I suspect you would need a much more powerfull amp like the viper 1200.1 or RF 1000bd
#3
Scooby Regular
Thread Starter
Join Date: Sep 2002
Location: Nottingham - HEY scumbag,leave my scoob alone!!!
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
MORE POWER
Just brought this Viper amp, was told it would be fine with this sub, how much power can these subs take? WHy won't 1 omh work?
PS I have a power cap and split charge system
[Edited by BigRed - 8/24/2003 11:17:30 AM]
Just brought this Viper amp, was told it would be fine with this sub, how much power can these subs take? WHy won't 1 omh work?
PS I have a power cap and split charge system
[Edited by BigRed - 8/24/2003 11:17:30 AM]
#4
Scooby Regular
Just seen your sub it is 600w rms
http://www.caraudiodirect.co.uk/shop/product_info.php?products_id=1241&tab=2
Yes your amp should power it. I would ask the installer to re-wire the system it may cure it. Or otherwise get the amp checked.
http://www.caraudiodirect.co.uk/shop/product_info.php?products_id=1241&tab=2
Yes your amp should power it. I would ask the installer to re-wire the system it may cure it. Or otherwise get the amp checked.
#5
Scooby Regular
Thread Starter
Join Date: Sep 2002
Location: Nottingham - HEY scumbag,leave my scoob alone!!!
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
rewired the install myself yesterday, took me all day mate
Do you think that my power cables are too long from my dist block, there around 1 meter each, there is also a kenwood kac923 amp runnig off the same dist block, that is closer than the viper amp ,maybe only 150mm cable, if i swap the amps around do you think this will cure the problem? I'm running both amps on 4 AWG cable and the earth is the same,power cap,split charge system etc.
Many thanks for any help
BigRed
[Edited by BigRed - 8/24/2003 6:03:24 PM]
Do you think that my power cables are too long from my dist block, there around 1 meter each, there is also a kenwood kac923 amp runnig off the same dist block, that is closer than the viper amp ,maybe only 150mm cable, if i swap the amps around do you think this will cure the problem? I'm running both amps on 4 AWG cable and the earth is the same,power cap,split charge system etc.
Many thanks for any help
BigRed
[Edited by BigRed - 8/24/2003 6:03:24 PM]
Thread
Thread Starter
Forum
Replies
Last Post