Apexi power fc problems
19 December 2010, 06:08 PM
#1
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2010
Posts: 280
Likes: 0
Received 0 Likes
on
0 Posts
Apexi power fc problems
I'm new to scoobynet only had my car 6 month just bought apexi power fc for my 97 uk turbo 2000 when fitted car would not start iv read you have to swap cam and crank sensor just wondering if any one has ecu pinout for this car iv searched every where can't find anything
19 December 2010, 06:11 PM
#2
I'm new to scoobynet only had my car 6 month just bought apexi power fc for my 97 uk turbo 2000 when fitted car would not start iv read you have to swap cam and crank sensor just wondering if any one has ecu pinout for this car iv searched every where can't find anything
19 December 2010, 06:15 PM
#3
Scooby Regular
iTrader: (3)
Join Date: Jan 2003
Location: Oss, The Netherlands
Posts: 749
Likes: 0
Received 0 Likes
on
0 Posts
Swap crank and cam, but on your model you would also have to replace the fuel pump controller wire to another pin. (it is on pin 8 now, and needs to go to the empty spot for pin 18, or vice versa)
Trending Topics
19 December 2010, 08:25 PM
#10
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
On the top biggest plug.
But the maf, injectors, cams, valves, pistons, turbo, intercooler are all different.
It will run but will damage the engine and needs fitting at time of mapping for no extra cost.
Simon
But the maf, injectors, cams, valves, pistons, turbo, intercooler are all different.
It will run but will damage the engine and needs fitting at time of mapping for no extra cost.
Simon
19 December 2010, 08:52 PM
#12
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2010
Posts: 280
Likes: 0
Received 0 Likes
on
0 Posts
Thanks alot so how many wires need changing is it three in total iv looked at your site what is the name of the number 7 wire also where are you from to get a remap I was thinking about just driving to where I'm getting the remap and changing the ecu then so am I right in think pinout 1 and 2 need changing and 7 needs moving to 17 like I said I'm new to all this but thanks for help also I'm fitting a td05 and I have some 440 injectors do I need to fit the injectors or not
19 December 2010, 09:06 PM
#13
Scooby Regular
iTrader: (1)
Join Date: Dec 2009
Location: Ayrshire
Posts: 1,145
Likes: 0
Received 0 Likes
on
0 Posts
You will need to fit the injectors if its only the 380s thats in there at the moment.
JGM will come to you and fit the ecu and swap the wires accordinly and as he stated at no extra cost...
JGM will come to you and fit the ecu and swap the wires accordinly and as he stated at no extra cost...
19 December 2010, 09:11 PM
#14
19 December 2010, 09:16 PM
#15
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2010
Posts: 280
Likes: 0
Received 0 Likes
on
0 Posts
I didn't know he came out to map it il have het intouch with him and get him out thanks alot mate you know how he charges iv done a few mods so was looking for a good mapper he's suppose to be one of the best have you contact details
Thread
Thread Starter
Forum
Replies
Last Post
