spec c to 400BHP? Ways to get there.....
#1
Scooby Regular
Thread Starter
iTrader: (4)
Join Date: Jan 2005
Location: Devon
Posts: 736
Likes: 0
Received 0 Likes
on
0 Posts
spec c to 400BHP? Ways to get there.....
Ok so I have a spec c running 363 BHP and 360 lb/ft but think its time for more.
Current mods are an induction kit and decat with evutek remap.
What are the next steps and is the bottom end safe to 400 on a spec c?
Cheers
Current mods are an induction kit and decat with evutek remap.
What are the next steps and is the bottom end safe to 400 on a spec c?
Cheers
#2
Scooby Regular
iTrader: (2)
Join Date: Mar 2001
Location: Here and there
Posts: 8,353
Likes: 0
Received 0 Likes
on
0 Posts
3 port boost solenoid,uprated actuator from turbo dynamics will assist.Personally id have stuck with the panel filter as you are probably drawing hot air into your induction kit zapping the power because that figure looks pretty poor to be honest
#3
Former Sponsor
Join Date: Dec 2005
Location: 10.68 QT mile in 2007 2.33 Type R ** Current 2002 Spec C 2.33 Track prepped.
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
Twin or single scroll ?
400 and over would mean turbo, injectors, remap and clutch. Engine is good for that and more.
400 and over would mean turbo, injectors, remap and clutch. Engine is good for that and more.
#4
Former Sponsor
iTrader: (3)
Join Date: Jan 2007
Location: London
Posts: 1,584
Likes: 0
Received 0 Likes
on
0 Posts
Copied from :
AndyForrestPerformance
03-07 STI JDM 2.0 /Type RA/ Spec C
Level 4 390-420 bhp
Full Decat turbo back 3” bore exhaust system
Custom flanged up/down pipes
Walbro 255 l/hr uprated fuel pump
K+N panel filter
Ecutek custom remap
NGK PFR 7B uprated spark plugs
Twin Port 650cc Injectors
Custom cold air induction
Custom version AFP 321H turbocharger to suit twin scroll headers
Level 5 430-460 bhp
Full Decat turbo back 3” bore exhaust system
Custom flanged up/down pipes
Walbro 255 l/hr uprated fuel pump
K+N panel filter
Ecutek custom remap
Twin boost set up for high/low power switchable in-car
NGK Racing 8 Spark plugs
Fuel Lab turbo specification fuel pressure regulator with fitting kit & gauge
Twin Port 650cc Injectors
Custom cold air induction
Custom version AFP 321T turbocharger to suit twin scroll headers
AVCR boost controller
Optional FMIC
Note For Level 5 we would recommend uprated steel rods & forged pistons and an uprated clutch.
AndyForrestPerformance
03-07 STI JDM 2.0 /Type RA/ Spec C
Level 4 390-420 bhp
Full Decat turbo back 3” bore exhaust system
Custom flanged up/down pipes
Walbro 255 l/hr uprated fuel pump
K+N panel filter
Ecutek custom remap
NGK PFR 7B uprated spark plugs
Twin Port 650cc Injectors
Custom cold air induction
Custom version AFP 321H turbocharger to suit twin scroll headers
Level 5 430-460 bhp
Full Decat turbo back 3” bore exhaust system
Custom flanged up/down pipes
Walbro 255 l/hr uprated fuel pump
K+N panel filter
Ecutek custom remap
Twin boost set up for high/low power switchable in-car
NGK Racing 8 Spark plugs
Fuel Lab turbo specification fuel pressure regulator with fitting kit & gauge
Twin Port 650cc Injectors
Custom cold air induction
Custom version AFP 321T turbocharger to suit twin scroll headers
AVCR boost controller
Optional FMIC
Note For Level 5 we would recommend uprated steel rods & forged pistons and an uprated clutch.
#5
Scooby Regular
#6
MD321T, Injectors & Remap. 400+ easy!
Dont listen to the "sucking warm air in" I monitor my air intake temps @ the MAF before and since I fitted my induction kit, temps are no warmer when on the move and thats where it counts,I've never experienced heat soak either.
Your current figures are bang on for your mods on a spec c.
Internals are fine for 400 also. So many others and myself running over 400 on standard internals.
Dont listen to the "sucking warm air in" I monitor my air intake temps @ the MAF before and since I fitted my induction kit, temps are no warmer when on the move and thats where it counts,I've never experienced heat soak either.
Your current figures are bang on for your mods on a spec c.
Internals are fine for 400 also. So many others and myself running over 400 on standard internals.
#7
Scooby Regular
iTrader: (3)
Join Date: Aug 2000
Location: 1600cc's of twin scroll fun :)
Posts: 25,565
Likes: 0
Received 2 Likes
on
2 Posts
Litchfield
Have a chat with Iain, their new twin scroll unit should be available soon plus they do a full 400+bhp package
For 400+ I wouldnt go single scroll, with the way twin scroll's are going, they will make a far better all round turbo over the single scroll units its just that they are still fairly new as turbo technology is concerned
Tony
Have a chat with Iain, their new twin scroll unit should be available soon plus they do a full 400+bhp package
For 400+ I wouldnt go single scroll, with the way twin scroll's are going, they will make a far better all round turbo over the single scroll units its just that they are still fairly new as turbo technology is concerned
Tony
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
crazyspeedfreakz
Wanted
17
05 October 2015 07:19 PM