wiring diagrams?
#1
Scooby Regular
Thread Starter
Join Date: Feb 2007
Location: south east
Posts: 115
Likes: 0
Received 0 Likes
on
0 Posts
wiring diagrams?
i am in need of a diagram for a MY99 rb5 i belive its a immobiliser problem,
the fuel pump isnt running i have checked the pump relay, witch is working fine,
can the immobiliser be got around any way.
dont really wanna wire a 12v feed off the igniton to the pump as i feel its a bit of of a bodgey way.
whats procedure if it need a new immobiliser systum. cost etc??
thanks
the fuel pump isnt running i have checked the pump relay, witch is working fine,
can the immobiliser be got around any way.
dont really wanna wire a 12v feed off the igniton to the pump as i feel its a bit of of a bodgey way.
whats procedure if it need a new immobiliser systum. cost etc??
thanks
#3
you wont find for an rb5 - but these might help. also try searching this forum for more links, (if search is working !!!) - there has been several posted in the past
Main Heading Goes Here
Extreme Machines
https://www.scoobynet.com/scoobynet-...ants-them.html
https://www.scoobynet.com/general-te...ml#post8026741
Main Heading Goes Here
Extreme Machines
https://www.scoobynet.com/scoobynet-...ants-them.html
https://www.scoobynet.com/general-te...ml#post8026741
Last edited by albob; 27 December 2008 at 05:25 PM.
#4
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
common for the plug connection under the back seat to corrode etc..
check for power at this plug and at the pump etc.
alternatively of course the pump could have failed.
Simon
check for power at this plug and at the pump etc.
alternatively of course the pump could have failed.
Simon
#7
Scooby Regular
Join Date: Oct 2005
Location: West London
Posts: 1,914
Likes: 0
Received 0 Likes
on
0 Posts
The Meta alarm/immobiliser on my 01 WRX did the same thing, internal realy died permanently immobilising the fuel pump.
Not sure where the wiring goes on the classic but I found the wiring fairly easily and just bypassed it until I got another alarm.
Not sure where the wiring goes on the classic but I found the wiring fairly easily and just bypassed it until I got another alarm.
Trending Topics
#8
Scooby Regular
iTrader: (8)
Join Date: Mar 2008
Location: west mids
Posts: 984
Likes: 0
Received 0 Likes
on
0 Posts
you will not get any wiring diag for your alarm/immobilizer for security reasons so specialist (appoved fitter only) but it sounds to me like a wire break down from the pump relay (in drivers door kick) to the connector under the back seat has become quite common fault on early classics as jgm is trying to point out to you..if its the immobilizer (Fuel pump curcuit break) at fault then may be able to help pm me!!!
Last edited by sy.; 28 December 2008 at 08:34 PM.
#9
Scooby Regular
Thread Starter
Join Date: Feb 2007
Location: south east
Posts: 115
Likes: 0
Received 0 Likes
on
0 Posts
i have power out of the relay but none at the black conector witch is in good condion. but wasnt sure if it then went throu the sigma alarm unit.
will check the wiring again from relay to pump
will check the wiring again from relay to pump
Last edited by 2-pump-tone; 28 December 2008 at 09:56 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Flat4x4-again
General Technical
2
29 September 2015 06:32 PM