scooby dead,, HELP<, fuelling perhaps ??
#1
Scooby Regular
Thread Starter
Join Date: Dec 2004
Location: Kendal, North west
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
scooby dead,, HELP<, fuelling perhaps ??
Felt bit flat yesterday, started her up today, ran for few hundred yards, felt hesitant, opened throttle little more, died on me, started again minute or two later, got her home, now just fires up and dies instantly,, HELP
what is most likely,, fuel pump ???
where can i take it in kendal as teg is packed solid and i ve no way to get it there, thanks steve
what is most likely,, fuel pump ???
where can i take it in kendal as teg is packed solid and i ve no way to get it there, thanks steve
#3
Scooby Regular
Thread Starter
Join Date: Dec 2004
Location: Kendal, North west
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
no i havent, i had the error code thing bookmarked but pc died and dont have the bookmark no more, any link greatfully appreciated, thanks
#4
Scooby Regular
Join Date: Jul 2006
Location: huddersfield
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
#5
Scooby Regular
Thread Starter
Join Date: Dec 2004
Location: Kendal, North west
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
thanks
fault code tested
35,23,11
so thats
35 Purge control solenoid valve
23 Mass air flow sensor
11 Crankshaft position sensor
anyone got any advice on parts etc, thanks
fault code tested
35,23,11
so thats
35 Purge control solenoid valve
23 Mass air flow sensor
11 Crankshaft position sensor
anyone got any advice on parts etc, thanks
#6
Scooby Regular
iTrader: (1)
Join Date: Aug 2005
Location: Manchester ish
Posts: 18,547
Likes: 0
Received 0 Likes
on
0 Posts
firstly I would reset the ecu, then run it and then check codes again (just to clear up what could be a pre existing code)
Im gonna go for it being the crankshaft sensor (think its probably the cheapest thing to replace as well)
Im gonna go for it being the crankshaft sensor (think its probably the cheapest thing to replace as well)
#7
Scooby Regular
Join Date: Jul 2006
Location: huddersfield
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
crank shaft sensor would stop the car running am sure and the others would cause uneven running but may clear up when crank shaft is changed if (suspect maf senser aint good ether) its still at fault after an ecu re set and see if runs then, think ive seen acrank sebsor on flea bay but second hand
Last edited by andyxros; 14 May 2008 at 09:40 PM.
Trending Topics
#9
Scooby Regular
Join Date: Jul 2006
Location: huddersfield
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
not sure never changed 1 but think its under altinator by flywheel but some 1 will know.. sorry
flywheel!!! why the hell did i put that i meant crank pully
flywheel!!! why the hell did i put that i meant crank pully
Last edited by andyxros; 14 May 2008 at 10:42 PM.
#10
Scooby Regular
iTrader: (18)
Join Date: Jul 2007
Location: Guildford Surrey
Posts: 693
Likes: 0
Received 0 Likes
on
0 Posts
Crank sensor is, front of engine, behind main crank pulley, below the altenator, you need a 10mm spanner to get the bolt out. Cam sensor is on the left hand head, behind the top cam pulley.
#13
Scooby Regular
Thread Starter
Join Date: Dec 2004
Location: Kendal, North west
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
followed instructions , given, connect black to black, green to green, hold accelerator for 20 secs, turn to ignition then count, ??/ wasnt that correct ???
anyways
admitted defeated , had her towed to garage this afternoon, they think fueling or air but aint getting started on her till tomorrow afternoon, just missing her,,lol, thanks all for help and who knows i may need more help if garage are left scratching there heads,
anyways
admitted defeated , had her towed to garage this afternoon, they think fueling or air but aint getting started on her till tomorrow afternoon, just missing her,,lol, thanks all for help and who knows i may need more help if garage are left scratching there heads,
#14
Scooby Regular
Join Date: Jul 2006
Location: huddersfield
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
dont know if you can at this stage but you need to set off down the road to full re set so ecu knows speedo etc works,then light should flash constant but sounds like sensor is goosed so need to iliminate some things by the sound of it
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM