HT leads ,are they worth uprating
12 September 2007, 06:53 PM
#1
Scooby Regular
Thread Starter
Join Date: Jul 2007
Location: dundee
Posts: 667
Likes: 0
Received 0 Likes
on
0 Posts
HT leads ,are they worth uprating
i'm getting NGK pfr7b spark plugs tommorow ,is it worth getting thicker HT leads aswell ,like magnacore 7mm or 8mm or there race spec ones i cant remember the name.
the car is a classic my00 sti with only a panel filter at the moment,
the car is a classic my00 sti with only a panel filter at the moment,
13 September 2007, 12:02 PM
#2
30 January 2008, 04:47 PM
#3
Scooby Regular
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
Ian
Trending Topics
31 January 2008, 01:59 PM
#8
Scooby Regular
Join Date: Mar 2005
Posts: 1,491
Likes: 0
Received 0 Likes
on
0 Posts
I've got the same car and replaced the leads with standard and Subaru are not particularly generous when it comes to the length of the leads. Could your lead to no.4 be slightly tight and heat/ vibration etc maybe causing it to pull off over time?
Kevin
Or a mischievous mouse, although they tend to eat my car!
Kevin
Or a mischievous mouse, although they tend to eat my car!
31 January 2008, 02:09 PM
#9
Scooby Regular
iTrader: (41)
Join Date: Nov 2003
Location: in the woods...........555 Wagon Sqn
Posts: 13,347
Received 55 Likes
on
42 Posts
I've got the same car and replaced the leads with standard and Subaru are not particularly generous when it comes to the length of the leads. Could your lead to no.4 be slightly tight and heat/ vibration etc maybe causing it to pull off over time?
Kevin
Or a mischievous mouse, although they tend to eat my car!
Kevin
Or a mischievous mouse, although they tend to eat my car!
my mischievous mouse lives under the kitchen floor and eats my cats food while they watch it
31 January 2008, 05:09 PM
#10
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
sounds like the problem.. if you look in the lead you can carefully squash it with pliers to make it a tighter fit.. Alternatively I think I have a set of secondhand my00 leads you could use one of the other leads from antoher cylinder that are longer?
father in-law had a mouse in his car.. it broke into a box of roses on the front seat and moved the whole lot to the boot.. father in-law saw this in the morning and then went out at lunchtime to clear up and they were gone.. stripped searched the car and they were behind the headlight!!!
the mouse chewed through lighting in the boot and a couple of other bits and put a mouse size hole in the rear seat.. he drove around with 3mouse traps in the car for a while..
Simon
father in-law had a mouse in his car.. it broke into a box of roses on the front seat and moved the whole lot to the boot.. father in-law saw this in the morning and then went out at lunchtime to clear up and they were gone.. stripped searched the car and they were behind the headlight!!!
the mouse chewed through lighting in the boot and a couple of other bits and put a mouse size hole in the rear seat.. he drove around with 3mouse traps in the car for a while..
Simon
Thread
Thread Starter
Forum
Replies
Last Post
hedgecutter
General Technical
3
25 September 2015 02:35 PM