ScoobyNet.com - Subaru Enthusiast Forum

Notices

where do i find

Thread Tools
 
Search this Thread
 
Old 16 December 2006, 04:39 PM
  #1  
haig007
Scooby Newbie
Thread Starter
 
haig007's Avatar
 
Join Date: Jul 2006
Location: crewe
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Unhappy where do i find
cant find the ecu connecter on my import m reg any help me what to check fault codes

ta lee
haig007 is offline  
Reply Like
Old 16 December 2006, 04:45 PM
  #2  
adrianp
Scooby Regular
 
adrianp's Avatar
 
Join Date: Jul 2006
Location: Ipswich
Posts: 161
Likes: 0
Received 0 Likes on 0 Posts
Default
This should help...

Scoobypedia | Trusted knowledge for everything Subaru | Reading ECU Fault Codes browse

Ady.
adrianp is offline  
Reply Like
Old 17 December 2006, 10:10 AM
  #3  
Jolly Green Monster
Former Sponsor
iTrader: (4)
 
Jolly Green Monster's Avatar
 
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes on 2 Posts
Default
when sat in the drivers seat they are by you left knee.. if they have not been used before they are often taped back into the loom.

Simon
Jolly Green Monster is offline  
Reply Like
Old 17 December 2006, 05:49 PM
  #4  
haig007
Scooby Newbie
Thread Starter
 
haig007's Avatar
 
Join Date: Jul 2006
Location: crewe
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Thumbs up cheers
what it is got miss fire or fuel cut off 3 and half grand 3 4 5 gear some time second change plug leads air flow anything else ive missed

cheers lee
haig007 is offline  
Reply Like
Old 17 December 2006, 09:47 PM
  #5  
Jolly Green Monster
Former Sponsor
iTrader: (4)
 
Jolly Green Monster's Avatar
 
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes on 2 Posts
Default
what plugs, and what gaps?

Simon
Jolly Green Monster is offline  
Reply Like
Old 23 December 2006, 12:37 PM
  #6  
haig007
Scooby Newbie
Thread Starter
 
haig007's Avatar
 
Join Date: Jul 2006
Location: crewe
Posts: 5
Likes: 0
Received 0 Likes on 0 Posts
Default
std plug set at 7mm
just rerooted me actuator off the reguator and seem not to bad. taken pipe of the reguator direct to maniford
haig007 is offline  
Reply Like
Old 23 December 2006, 09:37 PM
  #7  
Jolly Green Monster
Former Sponsor
iTrader: (4)
 
Jolly Green Monster's Avatar
 
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes on 2 Posts
Default
7mm!!! hope you mean 0.7mm

Hope you have sorted it then

Simon
Jolly Green Monster is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
OBD2 tracker and scanner
Sam Witwicky
Engine Management and ECU Remapping
17
13 November 2015 10:49 AM
Classic top hose diameter
TylerD529
General Technical
2
09 October 2015 01:53 AM
Will these fit?
blackieblob
ScoobyNet General
2
02 October 2015 05:34 PM
coil conversion type-r v6
makkink
General Technical
10
01 October 2015 05:41 PM
Oil dipstick reading on twinscroll
crazyspeedfreakz
ScoobyNet General
5
29 September 2015 05:04 PM
Back to Subforum
General Technical
View Next Unread
APEXI + CEL




Advanced Search
Quick Reply: where do i find


Reply Closed Thread Share
Forum Jump

All times are GMT +1. The time now is 11:33 AM.