APEXI + CEL
#1
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2005
Location: South Wales
Posts: 483
Likes: 0
Received 0 Likes
on
0 Posts
APEXI + CEL
Hi
Does anyone know if thees an option on the Apexi controller that turns on the CEL when you go over the apexi's limit to monitor boost I think its 1.25 bar.
Reason- even though the car has been set up and mapped for 1.45 bar it seems that every time I stray over 1.2/1.25 the cell light comes on, theres no knock, inj's are fine. In fact everything seems fine.
Any ideas?
Thanks
Does anyone know if thees an option on the Apexi controller that turns on the CEL when you go over the apexi's limit to monitor boost I think its 1.25 bar.
Reason- even though the car has been set up and mapped for 1.45 bar it seems that every time I stray over 1.2/1.25 the cell light comes on, theres no knock, inj's are fine. In fact everything seems fine.
Any ideas?
Thanks
#2
Scooby Regular
the power FC can be programmed to make the CEL come on for more than just boost issues.
Maybe your INJ are maxing out and that brings on the CEL. You have to talk to the mapper and ask what he set the CEL to come on for.
Maybe your INJ are maxing out and that brings on the CEL. You have to talk to the mapper and ask what he set the CEL to come on for.
#3
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2005
Location: South Wales
Posts: 483
Likes: 0
Received 0 Likes
on
0 Posts
Hi
Thanks, the inj's are fine only up to 70% , I could call the mapper, but its the weekend and I just wondered if anyone knew of a specific reason why the CEL would come on at over 1.2 bar boost.
Thanks, the inj's are fine only up to 70% , I could call the mapper, but its the weekend and I just wondered if anyone knew of a specific reason why the CEL would come on at over 1.2 bar boost.
#6
Originally Posted by JBJ
Hi
Does anyone know if thees an option on the Apexi controller that turns on the CEL when you go over the apexi's limit to monitor boost I think its 1.25 bar.
Reason- even though the car has been set up and mapped for 1.45 bar it seems that every time I stray over 1.2/1.25 the cell light comes on, theres no knock, inj's are fine. In fact everything seems fine.
Any ideas?
Thanks
Does anyone know if thees an option on the Apexi controller that turns on the CEL when you go over the apexi's limit to monitor boost I think its 1.25 bar.
Reason- even though the car has been set up and mapped for 1.45 bar it seems that every time I stray over 1.2/1.25 the cell light comes on, theres no knock, inj's are fine. In fact everything seems fine.
Any ideas?
Thanks
That is the Boost level if it Illuminates.
I cannot remember where the seting is though, The car did it on me when i 1st had it mapped.
Dean
Trending Topics
#8
Former Sponsor
iTrader: (4)
Join Date: Jan 2001
Location: ECU Mapping - www.JollyGreenMonster.co.uk
Posts: 16,548
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by JBJ
Hi
Does anyone know if thees an option on the Apexi controller that turns on the CEL when you go over the apexi's limit to monitor boost I think its 1.25 bar.
Reason- even though the car has been set up and mapped for 1.45 bar it seems that every time I stray over 1.2/1.25 the cell light comes on, theres no knock, inj's are fine. In fact everything seems fine.
Any ideas?
Thanks
Does anyone know if thees an option on the Apexi controller that turns on the CEL when you go over the apexi's limit to monitor boost I think its 1.25 bar.
Reason- even though the car has been set up and mapped for 1.45 bar it seems that every time I stray over 1.2/1.25 the cell light comes on, theres no knock, inj's are fine. In fact everything seems fine.
Any ideas?
Thanks
You should also be able to tell by going to ETC --> Sw/Sensor Check when the CEL is on and the problem should be highlighted on the screen..
Simon
#9
Scooby Regular
Originally Posted by Jolly Green Monster
PFC has no such features
Thread
Thread Starter
Forum
Replies
Last Post
Mister:E
Subaru Parts
2
24 September 2015 01:37 PM