Which intercooler for td05 16g?
23 December 2005, 09:54 PM
#1
Scooby Regular
Thread Starter
Join Date: Jun 2005
Posts: 1,938
Likes: 0
Received 0 Likes
on
0 Posts
Which intercooler for td05 16g?
Just treat myself to a new turbo (as above) for my MY00 UK.
Going to have a new intercooler added when the turbo is fitted.
Will a STi 5 intercooler be upto the job?
I'm after circa 320 bhp.
Current mods are full de-cat, panel filter and tek3 re-map (will be re-mapped when the turbo is fitted).
I'll have a new fuel pump fitted aswell.
Any other recommendations (preferably TMIC's).
Cheers
Going to have a new intercooler added when the turbo is fitted.
Will a STi 5 intercooler be upto the job?
I'm after circa 320 bhp.
Current mods are full de-cat, panel filter and tek3 re-map (will be re-mapped when the turbo is fitted).
I'll have a new fuel pump fitted aswell.
Any other recommendations (preferably TMIC's).
Cheers
23 December 2005, 10:00 PM
#2
Scooby Regular
Join Date: Sep 2000
Location: Deepest Darkest Dorset!!
Posts: 10,011
Likes: 0
Received 1 Like
on
1 Post
I have an intercooler off a newage wrx.... not to hard to fit, and bigger than the STI5 one aswell..... and best of all, it looks reasonably standard!
sp, thats is my my00 with TDO5 aswell as full decat, and K&N induction.... recently got 287 on the rollers, at a mere 4750 odd rpm, then it knocked back for some reason, so remapping will sort that, also started to use better fuel.... so shouldn't be too far off 310-320 when finished....
sp, thats is my my00 with TDO5 aswell as full decat, and K&N induction.... recently got 287 on the rollers, at a mere 4750 odd rpm, then it knocked back for some reason, so remapping will sort that, also started to use better fuel.... so shouldn't be too far off 310-320 when finished....
Last edited by RON; 23 December 2005 at 10:04 PM.
24 December 2005, 12:40 PM
#3
Scooby Regular
Join Date: Sep 2002
Location: midlands
Posts: 1,435
Likes: 0
Received 0 Likes
on
0 Posts
the sti5 IC is no bigger than your own IC. As Ron says you could fit a wrx new age with not too much effort or go for a sti7/8 one which is even bigger but requires a lot more effort to fit.
sti7 one here
http://www.sidtech.co.uk/iu/T5NYW092078501039.jpg
sti7 one here
http://www.sidtech.co.uk/iu/T5NYW092078501039.jpg
24 December 2005, 02:42 PM
#6
Scooby Regular
Join Date: Sep 2002
Location: midlands
Posts: 1,435
Likes: 0
Received 0 Likes
on
0 Posts
Matt you will need new age dump valve as the flange it bolts on is different. I retained mine as it was a forge item and changed the flange for a new age one. On the new age the pipe work from dump valve goes straight down from the dv then under IC. on the classic it comes out to the right.
ken
ken
Trending Topics
24 December 2005, 03:07 PM
#8
Scooby Regular
iTrader: (6)
Join Date: Apr 2005
Location: Stroke it baby!
Posts: 33,828
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by scooby_matt
What's required with fitting a newage wrx intercooler?
Also, will I need a new recirc valve?
Also, will I need a new recirc valve?
24 December 2005, 03:21 PM
#9
Scooby Regular
Join Date: Mar 2001
Location: uk
Posts: 1,998
Likes: 0
Received 0 Likes
on
0 Posts
thats is my my00 with TDO5 aswell as full decat, and K&N induction.... recently got 287 on the rollers, at a mere 4750 odd rpm, then it knocked back for some reason, so remapping will sort that
24 December 2005, 05:09 PM
#10
Scooby Regular
Join Date: Sep 2000
Location: Deepest Darkest Dorset!!
Posts: 10,011
Likes: 0
Received 1 Like
on
1 Post
HI John, no the operator didn't lift, he kept going, but the plot showed a definate dip at those revs, he reckoned it was cos i was running tesco 99.... (don't go there!!) also, the ecu hasn't been mapped specifically for my car yet, but i'll be getting the tek3 tweeked shortly i think..... the operator reckoned there'd be more to come if Optimax was used, but with that peak power being so low on the rev range, i'm hoping that once mapped the curve will keep going....
Mind you, the torque was 305lbft from about 3200 right through to 47?? then that dipped aswell... hence the assumption.....
Mind you, the torque was 305lbft from about 3200 right through to 47?? then that dipped aswell... hence the assumption.....
25 December 2005, 10:16 AM
#12
Scooby Regular
Thread Starter
Join Date: Jun 2005
Posts: 1,938
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Johnny50
I fitted an Sti8 tmic my MY00 wagon, as i had planned to fit the TD05 aswell.
Heres how it looks.
Heres how it looks.
What exactly is involved with fitted one, is it just brackets need making, or anything else?
25 December 2005, 10:32 AM
#13
Scooby Regular
Join Date: Sep 2002
Location: midlands
Posts: 1,435
Likes: 0
Received 0 Likes
on
0 Posts
Matt's shopping list
sti8 IC with aluminium 'Y' piece
sti 8 or wrx brackets + one home made one
sti or wrx dump valve
samco hose (elbow)
sti or wrx clutch mastercylinder (optional, can use yours cut down)
pipework for dump valve
that should cover everything
ken
sti8 IC with aluminium 'Y' piece
sti 8 or wrx brackets + one home made one
sti or wrx dump valve
samco hose (elbow)
sti or wrx clutch mastercylinder (optional, can use yours cut down)
pipework for dump valve
that should cover everything
ken
25 December 2005, 11:19 AM
#14
Scooby Regular
Thread Starter
Join Date: Jun 2005
Posts: 1,938
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by scooby-k
Matt's shopping list
sti8 IC with aluminium 'Y' piece
sti 8 or wrx brackets + one home made one
sti or wrx dump valve
samco hose (elbow)
sti or wrx clutch mastercylinder (optional, can use yours cut down)
pipework for dump valve
that should cover everything
ken
sti8 IC with aluminium 'Y' piece
sti 8 or wrx brackets + one home made one
sti or wrx dump valve
samco hose (elbow)
sti or wrx clutch mastercylinder (optional, can use yours cut down)
pipework for dump valve
that should cover everything
ken
Thread
Thread Starter
Forum
Replies
Last Post
Flat4x4-again
General Technical
2
29 September 2015 06:32 PM
