Defi Gauges Peak Warning settings please Help
#1
Scooby Regular
Thread Starter
Defi Gauges Peak Warning settings please Help
Had a set of Defi Gauges fitted recently not really to sure what the Peak warnings should be set @
The car MY01 WRX Teq 3 Full de cat Running 274 BHP Same torque
The gauges Oil press, Oil Temp, Boost.
Go the boost Set @ 1.3 Bar take it that this is o.k?
Not really to sure about oil temp / press Should be set to
Any help would be appreciated
Thanks in advance
Tiny...
The car MY01 WRX Teq 3 Full de cat Running 274 BHP Same torque
The gauges Oil press, Oil Temp, Boost.
Go the boost Set @ 1.3 Bar take it that this is o.k?
Not really to sure about oil temp / press Should be set to
Any help would be appreciated
Thanks in advance
Tiny...
#3
Ecu Specialist
Whats the idle oil pressure, whatever it is set the warning to about 0.1 bar below, so if ots 2.6 bar set to 2.5, 2 bar set to 1.9. that stops the beeper going off all the time at idle.
120 is a "good" level for oil, I set boost to just under my peak but suggest you set to 0.1 over and then you'll know when you overboost.
bob
120 is a "good" level for oil, I set boost to just under my peak but suggest you set to 0.1 over and then you'll know when you overboost.
bob
#4
Scooby Regular
Thread Starter
Originally Posted by Bob Rawle
Whats the idle oil pressure, whatever it is set the warning to about 0.1 bar below, so if ots 2.6 bar set to 2.5, 2 bar set to 1.9. that stops the beeper going off all the time at idle.
120 is a "good" level for oil, I set boost to just under my peak but suggest you set to 0.1 over and then you'll know when you overboost.
bob
120 is a "good" level for oil, I set boost to just under my peak but suggest you set to 0.1 over and then you'll know when you overboost.
bob
Thanks for the Reply guy's
Bob
Have just let the car idle When Cold, The oil pressure is reading between 6.0 & 7.0 (x100kpa) Or do i need to let it warm up then check the idle pressure ?
Have set the Oil Temp to 120oc
My peak boost reading on the s.e.c.s. Monitor is 1.37Bar But seems to hold about 1.20, 1.25 Bar Suggested setting ?
Sorry for the Q's But would like to get this set up Correctly, Had the Oil Temp buzzing all day Sat, Now know how to change
Thanks in advance again
Tiny...
#5
Scooby Regular
iTrader: (5)
Join Date: Feb 2003
Location: Worcester
Posts: 2,625
Likes: 0
Received 0 Likes
on
0 Posts
Tiny if you set the oil to 6.0 (x100kpa) it will be going off all the time I think mine is set to 2.8 x100kpa ( just bellow walm idle)
my secs says peak boost is 1.37 but think thats a bit of over boost when watching the gauges Im sure it goes to around 1.3 but Im sure Bob will be able to tell you if this is right . I have it set at 1.30 + a notch and it only really sounds on cold nights or when putting your foot flat to the floor in forth, doing say 2k revs to 5k
my secs says peak boost is 1.37 but think thats a bit of over boost when watching the gauges Im sure it goes to around 1.3 but Im sure Bob will be able to tell you if this is right . I have it set at 1.30 + a notch and it only really sounds on cold nights or when putting your foot flat to the floor in forth, doing say 2k revs to 5k
Last edited by WRX_Rich; 26 April 2004 at 10:33 PM.
#6
Tiny
I had an MY01 WRX before my JDM STi.
Bob mapped it (TEK3) to 1.28 bar on a fairly warm day on an accurate boost gauge.
The SECS read the ECU value as 1.39 bar. When the winter came round the gauge read a max of 1.3bar but the SECS showed 1.45
Nathan..
I had an MY01 WRX before my JDM STi.
Bob mapped it (TEK3) to 1.28 bar on a fairly warm day on an accurate boost gauge.
The SECS read the ECU value as 1.39 bar. When the winter came round the gauge read a max of 1.3bar but the SECS showed 1.45
Nathan..
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM