Has anyone fitted an uprated fuel pump / regulator to an STi4?
#1
Scooby Regular
Thread Starter
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Hi peebs,
Have any of you fitted an uprated fuel pump and / or regulator to your scoobs? If so please mail me some info on what pump / regulator you used, supplier contact details or URL. And if
possible some flow rate figures for the pumps.
Thanks
Pete
Have any of you fitted an uprated fuel pump and / or regulator to your scoobs? If so please mail me some info on what pump / regulator you used, supplier contact details or URL. And if
possible some flow rate figures for the pumps.
Thanks
Pete
#2
uprated pump went into my P1 last week, Walbro, supplied by Branco at Bob Rawle Developments in anticipation of the Tek 3 tomorrow. I think Mark Aigin on here can supply them - R19KET is user name. Don't know rate I'm afraid. Stuart at Scoobysport banged it in for me (Cheers m8)- I was a bit nervous about buggering about with the fuel tank and don't have anywhere covered at home, but its actually a piece of pi55, Back seats out - 5 bolts, sound deadening material removed, undo drivers side panel under the vertical part of the back seat - this exposes the actual tank access panel itself , disconnect all 3 fuel lines(out, return and vent) and electrical connector undo nuts ( remove from vicinity before you take the access panel off )extract fuel pump gubbins. The pump is just a push fit - it comes out easily and new one goes back easily, just bend the retaining bracket a bit to accomodate the new longer pump, the electrical connection attached to the new pump is a direct swap for the oem one.reverse above .
Runs nicely if a little bit louder than old one, car already seems smoother.
Runs nicely if a little bit louder than old one, car already seems smoother.
#3
Subaru Tuning Specialist
Join Date: Jun 2002
Location: 7.74 @179 mph 1/4 mile - road legal
Posts: 6,654
Likes: 0
Received 1 Like
on
1 Post
As above Pete, I'd speak to Mark A. I got my pump from him and it's well up to the job He has the flow curves etc.
The regulator I use is an FSE rising rate type but it is a pain to set up and even worse to map I believe With you having the Link I would recommend the regulator that Mark also supplies (webber ?)
Andy
The regulator I use is an FSE rising rate type but it is a pain to set up and even worse to map I believe With you having the Link I would recommend the regulator that Mark also supplies (webber ?)
Andy
#5
Scooby Regular
Thread Starter
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Cheers guys,
Just gettin the gen 2gether for "big red 2" (the reincarnation)
And wanna make sure everything is done. I`ll give Mark a bell and see what he`s got 4 me Barry, yeah i spoke 2 sam earlier n he told me about the marathon mapping session with u r regulator
Andy YHM shortly
Thanks again guys
Pete
Just gettin the gen 2gether for "big red 2" (the reincarnation)
And wanna make sure everything is done. I`ll give Mark a bell and see what he`s got 4 me Barry, yeah i spoke 2 sam earlier n he told me about the marathon mapping session with u r regulator
Andy YHM shortly
Thanks again guys
Pete
Trending Topics
#8
Scooby Regular
Thread Starter
Join Date: Mar 2000
Location: Tayside
Posts: 2,323
Likes: 0
Received 0 Likes
on
0 Posts
Harvey,
Yeah, just replied m8 I hit the sack early last night (auld age
catching up on me) so didn`t get it till 2day
Tony,
Not yet bud, still waiting to get the new engine in before deciding which way to go (keep it or sell it) no worries though
still got u on the list of peebs interested, if it`s being sold.
L8r
Pete
Yeah, just replied m8 I hit the sack early last night (auld age
catching up on me) so didn`t get it till 2day
Tony,
Not yet bud, still waiting to get the new engine in before deciding which way to go (keep it or sell it) no worries though
still got u on the list of peebs interested, if it`s being sold.
L8r
Pete
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
33
29 August 2017 07:18 PM