Heater matrix
#1
Scooby Regular
Thread Starter
Join Date: Mar 2014
Location: Hillingdon
Posts: 996
Likes: 0
Received 0 Likes
on
0 Posts
Heater matrix
Ok thank for all the help I now no it my matrix has gone . Don't really want to take the dash out . I have seen on e bay u can get this filler stuff that u put in the rad ,for £9.99 ish .they say it will find the hole and fill it .will this stop the leak . & stop the mist coming in the vents . Or am I just wish full thinking . Any help . Will this work or not
#3
Scooby Regular
Thread Starter
Join Date: Mar 2014
Location: Hillingdon
Posts: 996
Likes: 0
Received 0 Likes
on
0 Posts
1509joe . Will this work and it's call novastop . Will have a look for it . When I 1st worm the car up & put the heating on mist comes out of the vents and u can not see out of the front screen . But after a few mins it go's . But all way the next day it's back again . I no it's the matrex that's gone and even I small hole can make this happen . But as u no it means taking the dash out 1/2 day job .
#4
Scooby Regular
Thread Starter
Join Date: Mar 2014
Location: Hillingdon
Posts: 996
Likes: 0
Received 0 Likes
on
0 Posts
Hi this heater thing is not right today the mist only come in the vents for a few sec then it was gone . And the heater worked fine . Any idea on this.
& do u think this rad fix stuff will work . And how do u do it . Run the car for say 10 mins then put the heaters on full and making sure it's on the front screen . Then put the fans on full . Plus do I just put it in to the red . So undo the metal cap then pour it in. P.s the over flow by the battery shod that have water in I.e top that up as well or is it not ment to have water in till things go wrong.
Sound like I don't no much about this and u will be right . This is my 1st Subaru
& do u think this rad fix stuff will work . And how do u do it . Run the car for say 10 mins then put the heaters on full and making sure it's on the front screen . Then put the fans on full . Plus do I just put it in to the red . So undo the metal cap then pour it in. P.s the over flow by the battery shod that have water in I.e top that up as well or is it not ment to have water in till things go wrong.
Sound like I don't no much about this and u will be right . This is my 1st Subaru
Last edited by Jayjay100; 09 May 2014 at 04:27 PM.
#5
Scooby Regular
iTrader: (2)
Empty some water out of the header tank on the manifold start the engine with cap off. Warm engine up to operating temperature. Pour in half the bottle top up replace cap. Heater on and run at fast idle for ten minutes. DO NOT PUT ANY IN EXPANSION TANK NEXT TO THE BATTERY. Job done. Yes the bottle next to the battery should have coolant in it fill to max mark.
Last edited by 1509joe; 10 May 2014 at 12:30 AM.
#7
Unmapped 12.4s @ 105
iTrader: (29)
Join Date: Apr 2005
Location: Newcastle. 330bhp-289lb/ft @ 1bar boost - 12.4s @ 105mph
Posts: 11,776
Likes: 0
Received 4 Likes
on
4 Posts
Radiator is aluminium, would assume the heater matrix is also. The heads and the block are aluminium.
What do you thinks going to the water galleries?
What do you thinks going to the water galleries?
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
33
29 August 2017 07:18 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
38
17 July 2016 10:43 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM