Notices
Drivetrain Gearbox, Diffs & Driveshafts etc

DIY service

Thread Tools
 
Search this Thread
 
Old 17 October 2004, 10:26 PM
  #1  
JohnnyR6
Scooby Regular
Thread Starter
 
JohnnyR6's Avatar
 
Join Date: Jul 2003
Posts: 673
Likes: 0
Received 0 Likes on 0 Posts
Default DIY service

HI folks, i'm gonna service my scoob soon (my95 STI2). As it's my first time doing the scoob are there any tips? I know the oil change procedure but what about the plugs? Any special tools needed or anything to watch?

Cheers Johnny
Old 17 October 2004, 11:19 PM
  #2  
StickyMicky
Scooby Regular
 
StickyMicky's Avatar
 
Join Date: Feb 2003
Location: Zed Ess Won Hay Tee
Posts: 21,611
Likes: 0
Received 0 Likes on 0 Posts
Default

plugs are tricky
you need an assortment of flexi joints and extension bars to get in properlly

wind the plugs in by hand a bit before you tighten them up with a ratchet as its pretty hard to see exactly what your doing half the time
Old 17 October 2004, 11:58 PM
  #3  
Scoob+Bike=Fun
Scooby Regular
 
Scoob+Bike=Fun's Avatar
 
Join Date: Jun 2004
Posts: 441
Likes: 0
Received 0 Likes on 0 Posts
Default

leave the plugs out until you have put fresh oil in, then crank it with the new oil in for 30m seconds, then put the plugs in, i have read it on this board that this is the best way, and if you dont, it could harm your engine
Old 18 October 2004, 09:20 AM
  #4  
Peanuts
Scooby Regular
iTrader: (15)
 
Peanuts's Avatar
 
Join Date: Jul 2001
Location: Portsmouth
Posts: 8,606
Likes: 0
Received 0 Likes on 0 Posts
Default

read the handbook for the correct amount of fluids to add and gauge them oput before you start pouring, that way you will know how much to put in, then just check the levels in the normal way and make your fine adjustments
Old 18 October 2004, 09:25 PM
  #5  
JohnnyR6
Scooby Regular
Thread Starter
 
JohnnyR6's Avatar
 
Join Date: Jul 2003
Posts: 673
Likes: 0
Received 0 Likes on 0 Posts
Default

Cheers lads, although i can't read my handbook as it's in japanese..lol
Old 19 October 2004, 08:20 AM
  #6  
richieh
Scooby Regular
 
richieh's Avatar
 
Join Date: Jun 2003
Location: pencoed s wales
Posts: 1,357
Likes: 0
Received 0 Likes on 0 Posts
Default

wind the plugs in with rubber hose it stops them cross threading
remove airbox and battery for better access
ive got a 3in extension bar which gives perfect fit/length with a plug socket
a wobble joint is easier because the plug +socket and bar are a little tight against the chassis rail
are you doing the gearbox oil,diff oil and cambelt as well?
richie
Old 19 October 2004, 09:30 AM
  #7  
:eek:
Scooby Regular
 
:eek:'s Avatar
 
Join Date: Dec 2003
Location: Saaf Oxhey
Posts: 378
Likes: 0
Received 0 Likes on 0 Posts
Exclamation OIL

Make sure you fill the new oil filter with clean oil before fitting it....be warned they may look small but they hold a helluva lot of fluid, fill it, let it stand, fill it again, let it stand, ......i did this 4 times when i changed my oil
Old 20 October 2004, 12:46 PM
  #8  
EddScott
Scooby Regular
 
EddScott's Avatar
 
Join Date: Sep 2003
Location: West Wales
Posts: 12,573
Received 64 Likes on 32 Posts
Default

I posted this a while ago as a DIY service schedule.

Engine Oil - every 4 months, car isn't driven hard and does about 700 a month
Gearbox and rear diff - Every 12 months
Plugs - Every 12 months
Maf and Lambda - Every 24 months - dependent if MAF pops in between time
Fuel Filter - Every 18 months

Brake fluid change performed by local Subaru Specialist. Also would take car to said specialist every 6 months for inspection of things like CV boots etc and just a good check over for faults.

One thing I haven't included is power steering fluid - when should that be changed?
Old 20 October 2004, 11:24 PM
  #9  
scoobypreza
Scooby Regular
 
scoobypreza's Avatar
 
Join Date: Feb 2003
Posts: 1,449
Likes: 0
Received 0 Likes on 0 Posts
Default

Changed my oil and plugs a few weeks back and found it easier to change the plugs using a 3/8 drive ratchet rather than 1/2 inch. Most of the time is taken removing things to get to the plugs but when you've moved airbox, battery etc it only takes a couple of minutes to do the plugs.

Dave
Old 21 October 2004, 05:01 PM
  #10  
Baggers
Scooby Regular
 
Baggers's Avatar
 
Join Date: Oct 2004
Posts: 204
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by Scoob+Bike=Fun
leave the plugs out until you have put fresh oil in, then crank it with the new oil in for 30m seconds, then put the plugs in, i have read it on this board that this is the best way, and if you dont, it could harm your engine
30m seconds, as in half a minute or 30 milliseconds? Anybody have more info on this procedure and the reasons for it, I don't understand why?
Old 21 October 2004, 05:58 PM
  #11  
Leroi
Scooby Newbie
 
Leroi's Avatar
 
Join Date: Jul 2004
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Default

I think i need a new battery as my car wont travel 30 metres in a second on the starter motor.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
KAS35RSTI
Subaru
27
04 November 2021 07:12 PM
Abx
Subaru
22
09 January 2016 05:42 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM



Quick Reply: DIY service



All times are GMT +1. The time now is 08:41 AM.