Quickshift Fitting
#1
Quickshift Fitting
I have done a search about fitting a quickshift. I have an MY97.
It looks as though you need to just force the old stick out of the ball joint and then just **** the new one hard enough till it pops in.
I don't like being too rough with my scoob so could someone please tell me if this is correct before I get tough with her . . . . . .
Thanks
Ian
It looks as though you need to just force the old stick out of the ball joint and then just **** the new one hard enough till it pops in.
I don't like being too rough with my scoob so could someone please tell me if this is correct before I get tough with her . . . . . .
Thanks
Ian
#2
Scooby Regular
Join Date: Jun 2002
Location: The home of the game played with odd shapped balls
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
I fitted a B&M Quickshift to my my95 and it was basicly what you say there, except that the white plastic collar in at the bottom of the original gear stick has a cut out in it to allow you to close the gap and remove it whithout breaking the plastic collar, however mine broke anyway but then are only a £5 from a subaru dealer if you need to replace it when reinstalling the original stick. The B&M has an anodised collar with two O-rings rather than a plastic one so it was pretty easy to fit.
I found it was best have the **** on the sick when installing so you can exert some pressure to push the new gear stick home.
I found it was best have the **** on the sick when installing so you can exert some pressure to push the new gear stick home.
#4
Scooby Regular
Join Date: Jun 2002
Location: The home of the game played with odd shapped balls
Posts: 2,037
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by scoobylav
Mine doesn't have the white plastic collar I don't think. It looks just like a ball at the bottom that fits into a white socket, unless it is this you mean.
Sorry if ive not helped to clear things up
#7
Scooby Regular
Just pull the old gear stick back (unbolt the pivot first!!) and it should pop out.
Put a block between the bottom of the shifter and the prop shaft. (Takes out the movement in the gearbox when you "****" the new one in)
Put a block between the bottom of the shifter and the prop shaft. (Takes out the movement in the gearbox when you "****" the new one in)
Trending Topics
#8
Scooby Regular
Join Date: Apr 2003
Location: Location: Location:
Posts: 1,097
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Butty
If you don't want to **** it then the proper way is to get under the car and remove the circlip that holds the ball in the socket.
Everything then pulls out nice and easy.
Nick
Everything then pulls out nice and easy.
Nick
Originally Posted by RRH
....and falls to bits just **** it. it will be fine!
I'm in the same position, I got the original shifter out of the socket, but I've been "twatting" it for ages trying to get the new one in and I've got sore hands now
I glanced at the manual, it mentions taking off the exhaust, heatshield etc etc too much! Do I really have to go to all this bother? If I undo the four bolts around the plate, will a load of stuff hit the garage floor?
#12
Scooby Regular
iTrader: (2)
Originally Posted by scoobylav
Jiggerypokery what year is yours ?
Butty I thought the circlip was accessable from the top i.e inside
Butty I thought the circlip was accessable from the top i.e inside
Undoing the four bolts will just let the gear change fall on top of the mid section.
To undo the circlip really needs the mid section off but the underbody heat shiled can stay on.
If you must **** it then perhaps wedging something to stop the g/change socket from moving down would work (although I've never tried it).
The wedge would have to go betweeen the exhaust mid section and the socket, or say a length of wood that is wedged tight against the ground to the socket would do the trick.
Nick
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
33
29 August 2017 07:18 PM
JonMc
Subaru Parts
22
06 February 2016 09:50 PM
matt12
ScoobyNet General
64
16 September 2015 09:16 PM
matt12
Engine Management and ECU Remapping
4
14 September 2015 09:36 AM