Like white grease type of stuff? Mine won't be doing many miles when finished, 2000 miles a year tops. I'll put up with the clunking. What make have you got? Do they hold up alright over time?

 

I had whiteline drop-links up front that fell apart; the Perrin ones I have now hold up a lot better. The lateral arms are unbranded and the rubber boots rotted but the rose joints are fine. I use spray on silicone spray - like WD40 only better. It keeps them relatively corrosion free given the cr4p on our roads especially in winter. I do a similar mileage too

I do see some corrosion on the drop-links but thats' areas that aren't in contact with other metal so don't seem to lube themselves

 

They are very sparing round where I live with salt, main problem is potholes and just **** roads. Defo gunna be choosing my roads when this car is finished. My cars been parked outside for 13 years and never garaged by previous owner and we live near the sea, plenty of rust I can assure you! A lot of it is surface (still looks ****) but I'm getting quite a big scrap pile.

 

got some stuff back from powder coatings at the weekend and im really impressed with it can't wait to bolt them back up! also got some r180 rear hubs. Cut my spare wheel well out too and got all the underseal off.


























Now, i've cut the spare wheel well out but i presume you have to cut the rear slam panel too otherwise there would be a lot of drag?

 

coming along nicely mate

 

Not updated in a while, so here's some pics of what's been happening! Been repairing my shell cos there was quite a bit of rust lurking about, mainly because it has had a rear quarter on (about 13 years ago mind you) and possibly wasn't sealed properly, I dunno but that's where the rust is! Made the structure for the jacking point (osr) and the inside of the sill near the rear arch. Not made the outer part of the sill yet as I'm waiting to buy to ABW arches and want to see where they lie. All the areas that are red is where new parts have been made, I'm keen with the red oxide haha.... And sikaflex. Seam welded my front end, in the middle of making my fender braces. All rollcage mountings welded into the car and sound proofing off. Got my CDS which needs bending still, struggling to find someone, might just buy the main hoop from custom cages yet.









I made that piece for the wing to create and cold air feed box, planning on ducting through fog light the cuttin a hole coming up into it.

 

 

Got a new subaru part carrying vehicle too, must admit I do enjoy vtec.

 

It's a shame you're not nearer to me - I need some welding done in the engine bay and you've done a tidy job

 

Thanks, the welder was a good investment! Definitely got the hang of it all now. What you need doing in your engine bay? My battery tray was hanging!

 

I want to weld up were some of the spot welds went through when I removed the battery tray, plate up some surplus holes and generally tidy up the inner wings

 

Ah I see , similar to me then, I just need to buy some filler to smooth out the turrets then its in with some primer, looking forward to getting all in one colour. I want to try and keep it all pretty minimalistic in the engine bay, think it looks better. This was it before hand and it looks too busy.

 

There will be no abs, relocating the battery and the screen wash bottle, no aircon, and lots of shiny bits!

 

Yeah, but I've not taken the engine out so the colour bit is going to be fun - mine's looking like this at the moment...



ABS and aircon have gone, battery is in the boot and I just need to tidy it up...





The washer bottle has been replaced with a smaller on and I am going to use the space for my catch can. I've also been doing some inlet smoothing




So you can see the finish of the inner wings is going to let it all down

 

Mine is the same but it's too big a job for me I think, i've not welded for years.

What Rota's are they Jon?

 

Rota GTRs mate, 8x18 on an ET of 48



And I found this one of my washer bottle

 

That is a bonny bug. I like that washer bottle where's it from?do u smooth inlets with a sanding disc?

 

Washer bottle was one of these I used some spare alloy I had in the garage to make the mounting bracket.

http://www.ebay.co.uk/itm/HYUNDAI-S-...item19dd8faa54

Smoothing was done with an angle grinder, set if files, orbital sander, a dremel and lots of emery paper - it's a bit rough up close but I'm going to get some takes off for the FPR and DV welded on and a bodyshop to finish it off along with my TGV deletes and add a coat of wrinkle black

 

Sounds like a lot of work, but then again it's worth it cos they look good when finished. The newage inlets look a lot tidier than the classics, mines a v4 one with bits sticking out everywhere. Think I'm gunna do the otherside inner wing tomorrow, it'd just be lazy if I didn't! Then got under the arch on the n/s/f and seam weld. And I can finish my fender braces too. Should be a productive weekend

 

I've taken a whole load of lugs and take offs off, and may yet do the servo one just to finish it. Didn't help that I kept on finding more to do, all that's left now is the lugs for the header tank

 

Don't talk to me about smoothing bleeding manifolds!

 

Between you and the metal master you can finish mine off, should package it all up this weekend for you

 

Pah!

 

That looks the bollocks. Dread to the think how long that took! Girlfriend fails to see any kind of difference between the two manifolds

 

Did the other side of the engine bay today, it looks sweet, pics up tomorrow. But then found more rust on my back quarter under the rear quarter glass and just at the top of the c pillar next to the roof trim. Been sanding that down to bare metal but ideally need to pop that window and my rear screen out, any ideas on the best way to do this?

 

This looks like it is going to be fit, suscribed

 

Quick update, not had much time to do much over the weekend as a friends dog went missing in the lakes so been up there finding the basterd, which we didn't... Anyway, I did make an air duct, got it welded in the car and have got a bit of filler on it, it's not finished yet but it was getting a bit tedious so made myself a strut brace.