THE FORCE AWAKENS.
#151
My K&N recharge kit turned up today so thought that i would get on with it...
I started by taking the filter off,the instructions said to spray both sides of the filter all around and let it sit for ten minutes allowing the cleaner to penetrate the dirt,i thought that as it had some big bits of dirt stuck on the filter i would try to blow them out first...
The filter was then sprayed with the cleaner and left to sit for ten minutes...
The jubilee clip was looking kind of grubby so thought that as it was off i would give it a quick clean with some metal cleaner...
The filter was rinsed out thoroughly after ten minutes had passed...
And Put down on a tray to air dry naturally...
It still looks fairly dark but its completely clean,the dark appearance is because i have not lightly sprayed it back with the K&N recharge oil yet that will be done after i allow it to fully dry and then it will have the salmon pink colour back.SJ.
I started by taking the filter off,the instructions said to spray both sides of the filter all around and let it sit for ten minutes allowing the cleaner to penetrate the dirt,i thought that as it had some big bits of dirt stuck on the filter i would try to blow them out first...
The filter was then sprayed with the cleaner and left to sit for ten minutes...
The jubilee clip was looking kind of grubby so thought that as it was off i would give it a quick clean with some metal cleaner...
The filter was rinsed out thoroughly after ten minutes had passed...
And Put down on a tray to air dry naturally...
It still looks fairly dark but its completely clean,the dark appearance is because i have not lightly sprayed it back with the K&N recharge oil yet that will be done after i allow it to fully dry and then it will have the salmon pink colour back.SJ.
Last edited by stonejedi; 11 April 2020 at 05:45 PM.
The following users liked this post:
#152
Finally got around to spraying my filter as my rinse stage was to goodand it took a few days for it to be completely dry, the ends was taped up as I wanted the jubilee clip to be able to tighten up properly without slipping off the rubber...
I noticed that the K&N filters seem to be over oiled from the factory,it came out a very light salmon colour after my wife sprayed it for me...i decided that i would leave it for 24 hours for the oils to soak in before i refit it back on my car tomorrow.SJ.
I noticed that the K&N filters seem to be over oiled from the factory,it came out a very light salmon colour after my wife sprayed it for me...i decided that i would leave it for 24 hours for the oils to soak in before i refit it back on my car tomorrow.SJ.
#153
I woke up nice and early this morning and refitted my K&N air filter now it has been fully cleansed and recharged,I then decided to give my car a quick wash...
I have a little mod in mind that I will be doing to my car later on...while i am still waiting for my quick rack...It is supposed to be getting delivered this afternoon according to the tracking.SJ.
I have a little mod in mind that I will be doing to my car later on...while i am still waiting for my quick rack...It is supposed to be getting delivered this afternoon according to the tracking.SJ.
The following 3 users liked this post by stonejedi:
The following users liked this post:
#155
Scooby Regular
The following users liked this post:
The following 2 users liked this post by stonejedi:
#162
Scooby Regular
#166
Scooby Regular
How much did you pay for the rack if you don't mind me asking quite fancy one my self
#167
Scooby Regular
#169
The following users liked this post:
#170
A little bit of metal polishing done today, my exhaust had lost a bit of it's shine...
I decided to use a metal polish from Britemax that i had in my shed...
I read the directions and proceeded to get to work...
Applied to the exhaust and worked in...
After spending some time rubbing the metal polish in to the exhaust,it started to look a lot better
.SJ.
I decided to use a metal polish from Britemax that i had in my shed...
I read the directions and proceeded to get to work...
Applied to the exhaust and worked in...
After spending some time rubbing the metal polish in to the exhaust,it started to look a lot better
.SJ.
The following 2 users liked this post by stonejedi:
#171
Scooby Regular
I find autosol is fantastic mate, what did you use?
#173
Scooby Regular
The following users liked this post:
#175
Just for you Kaosone,i have found the pictures of when my CAE shifter was fitted.I have had it on my car for quite a while now, just forgot about it as its the norm for me now...Anyway its quite a story as it was all fitted by my lovely Wife...I was ill at home and after waiting around 2 months for it to arrive all i could do was look at itSo my wife googled the fitting instructions online and asked me for my car keys...She removed the STI gear shifter from my car at that time I knew that she meant business...
Last edited by stonejedi; 25 April 2020 at 11:21 PM.
#180
Scooby Regular
Depends, is she ant good at rocker cover gaskets?
Knock knock...
Just play the hand you’re dealt
Knock knock...
Whose there?
.Subaru main bearing
Just play the hand you’re dealt
Last edited by Kaosone; 26 April 2020 at 08:40 AM.