MY95 rev counter
10 May 2002, 10:08 AM
#2
Scooby Regular
Join Date: May 2002
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
Try ringing this geezer, he's my mates brother and he has been known to break the odd Impreza.
His name's Liam Wood and you can reach him on: 01343 850 439
or 07788 585 598
Failing that, mail him at - liam@glenbcars.fsnet.co.uk
HTH!
His name's Liam Wood and you can reach him on: 01343 850 439
or 07788 585 598
Failing that, mail him at - liam@glenbcars.fsnet.co.uk
HTH!
10 May 2002, 02:55 PM
#4
Scooby Regular
Join Date: May 2002
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
I will get on his case then!!
Seriously, i think he's quite busy just now, that's why me and Mr Wood are here instead of him!! Better to ring him i reckon, he's a top notch bloke and in no way offensive at all so if you can, phone!
Will tell Callum (Mr Wood) to tell his bro to get his **** in gear and get on the comp!
Seriously, i think he's quite busy just now, that's why me and Mr Wood are here instead of him!! Better to ring him i reckon, he's a top notch bloke and in no way offensive at all so if you can, phone!
Will tell Callum (Mr Wood) to tell his bro to get his **** in gear and get on the comp!
11 May 2002, 12:48 AM
#5
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Cheers mate, I actually got a reply from him a few hours ago, but somehow he managed to misunderstand and think that I was looking for the speedo... I'll give him a call, does he work on Saturday's, you happen to know? Or should I wait until Monday (so someone else gets to buy the darn thing before me!)?
* Miki *
* Miki *
14 May 2002, 12:18 PM
#7
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
I just put a check on it's way to Scotland... Liam promised to send me what I need!
Now I just need to ensure how to remove the freakin needle without destroying this revcounter as well, according to scooby_si the best way is to melt off the old one, but doesn't that warm up the revcounter too much, after all, the pin is a metal thing?
* Miki *
[Edited by Miki - 5/14/2002 12:19:17 PM]
Now I just need to ensure how to remove the freakin needle without destroying this revcounter as well, according to scooby_si the best way is to melt off the old one, but doesn't that warm up the revcounter too much, after all, the pin is a metal thing?
* Miki *
[Edited by Miki - 5/14/2002 12:19:17 PM]
Trending Topics
15 May 2002, 09:01 AM
#9
Scooby Regular
Join Date: May 2002
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Why can you not just put the whole clock assembly in as one? That is what Liam will send you so you could just un-screw the old clocks and screw in the new ones! Jobs a good one!
Regards Callum.
Regards Callum.
07 June 2002, 06:40 AM
#12
Scooby Regular
Thread Starter
Join Date: Dec 2001
Location: Finland
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
I have a revcounter again... I have a REVCOUNTER again... I HAVE A REVCOUNTER AGAIN !!!!!! 
Dunno if I got the needle back in the correct position though, cause the fun stops at exactly 7000revs now... can anyone tell how much I got it wrong (MY95)? I guess the rev cut should be a bit more than 7000, or am I wrong? If it's only a couple of hundred revs I won't touch it, too afraid I'll mess up the darn thing again.
-Miki-
Dunno if I got the needle back in the correct position though, cause the fun stops at exactly 7000revs now... can anyone tell how much I got it wrong (MY95)? I guess the rev cut should be a bit more than 7000, or am I wrong? If it's only a couple of hundred revs I won't touch it, too afraid I'll mess up the darn thing again.
-Miki-
Thread
Thread Starter
Forum
Replies
Last Post
aaron_ions
General Technical
17
03 November 2021 11:07 AM
matt12
Engine Management and ECU Remapping
4
14 September 2015 09:36 AM