Phase 2 Fuel Rails.
09 October 2002, 03:54 PM
#1
Scooby Regular
Thread Starter
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
Anybody got a set of phase 2 rails kicking about that they want to sell.. Injectors not required..
David
David
09 October 2002, 04:15 PM
#2
Scooby Regular
Thread Starter
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
ok now I havent got a clue... after speaking with howard chopping apparently theres loads of types...
David
David
10 October 2002, 04:18 PM
#5
Any fuel rail from a 99-00 subaru should do, they should have yellow injectors in as per the left one in the picture above.
Could come from the following cars:
uk 99-00
wrx 99-00
STI 5
STI 6
P1
Possibly 98-99 legacies (tend to be a year ahead)
Forester turbo?
Paul
Could come from the following cars:
uk 99-00
wrx 99-00
STI 5
STI 6
P1
Possibly 98-99 legacies (tend to be a year ahead)
Forester turbo?
Paul
10 October 2002, 04:22 PM
#6
Scooby Regular
Thread Starter
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
no longer an immediate requirement...
Harvey is driving down with some (well additional to the ones on his car)
Top Bloke..
Few pints shall be bought for this..
David
Harvey is driving down with some (well additional to the ones on his car)
Top Bloke..
Few pints shall be bought for this..
David
Trending Topics
11 October 2002, 08:40 AM
#9
Scooby Regular
Thread Starter
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
ARGH...
Harvey is only lending me his... I may have a source though..
David
Harvey is only lending me his... I may have a source though..
David
11 October 2002, 11:14 AM
#10
David,
I'm confident of phase 1 fitment, if you have phase 1 injectors out, then a picture, drawing and accurate dims would be a good start. It's not really practicle for me to keep removing injectors, and the fuel spill stinks for ages.
Paul
I'm confident of phase 1 fitment, if you have phase 1 injectors out, then a picture, drawing and accurate dims would be a good start. It's not really practicle for me to keep removing injectors, and the fuel spill stinks for ages.
Paul
11 October 2002, 11:19 AM
#11
Scooby Regular
Thread Starter
Join Date: Nov 2001
Location: Leeds - It was 562.4bhp@28psi on Optimax, How much closer to 600 with race fuel and a bigger turbo?
Posts: 15,239
Likes: 0
Received 1 Like
on
1 Post
hmm... im relatively (sp) confident, but its a lot of work which I dont have time for, (dont even have time to go find a length of ally rod)
Where as phase 2 rails.. job done..
David
Where as phase 2 rails.. job done..
David
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
bluebullet29
General Technical
9
05 October 2015 02:17 PM