When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors.
Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also.
These are required for 2 reasons when fitting aftermarket speakers to scoobs.
1) adapter for the 3 to multiple fittings
2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down...
Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go!
Fitment
- newage fronts (either 6.5" or 5.25" speakers) and rears (To fit 5 1/4" speakers) - variant 1
- classics - variant 2
Costs
Newage fronts 6.5": £17.50 + postage gifted on PayPal
Newage fronts 5.25": £16.00 + postage gifted on PayPal
Newage rears 5.25": £15.00 + postage gifted on PayPal
Classic fronts 6.5" = £16.00 + postage gifted on PayPal
Postage is: £2.95 RM 2nd class, £3.50 RM 1st class.
These can be printed to order and I will need about 48 hours before shipping. PM me for ordering.
Cheers for looking!
Last edited by Bazil_SW; Dec 15, 2018 at 06:07 PM.
Ok, but not as good as I was hoping for! They haven't been much difference over stock I don't think, which is surprising considering how much bigger they are!
Ok, but not as good as I was hoping for! They haven't been much difference over stock I don't think, which is surprising considering how much bigger they are!
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors.
Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also.
These are required for 2 reasons when fitting aftermarket speakers to scoobs.
1) adapter for the 3 to multiple fittings
2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down...
Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go!
Fitment
- confirmed: Hawk
- presumed all newage as the same speakers and door casings were used on earlier models
- presumed classics (assume same hole centres for the stock 3 screws. i.e. 150m if you measure centre to centre between any 2 of the mounting holes)
Cost: £17.50 + postage gifted on PayPal
Postage is: £2.50 RM 2nd class, £3.50 RM 1st class.
These can be printed to order. PM me for ordering.
Cheers for looking!
Hi would be interested in a set if you can make them for 5.25 inch
Hi would be interested in a set if you can make them for 5.25 inch
Can do, if you can confirm the distance between 2 opposite mounting holes on your speakers that would help. I think it's 118mm from what I can find, but there seems to be some variation. They can be slightly cheaper too since they will be smaller, can work out it later.
Not yet, but I was thinking of taking a look at them as they are smaller I believe, probably 4 inch as stock?
mill today and a look on the weekend mate if you would be able to I would order a full set as the ones that come with the speaker touch the door cards haha 😂
mill today and a look on the weekend mate if you would be able to I would order a full set as the ones that come with the speaker touch the door cards haha 😂
Sounds good mate, drop me a pm and we can sort something out
3D Printed Front and Rear Door Speaker Spacers
