3D Printed Front and Rear Door Speaker Spacers
Hi all,
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors. Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also. These are required for 2 reasons when fitting aftermarket speakers to scoobs. 1) adapter for the 3 to multiple fittings 2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down... Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go! Fitment - newage fronts (either 6.5" or 5.25" speakers) and rears (To fit 5 1/4" speakers) - variant 1 - classics - variant 2 Costs Newage fronts 6.5": £17.50 + postage gifted on PayPal Newage fronts 5.25": £16.00 + postage gifted on PayPal Newage rears 5.25": £15.00 + postage gifted on PayPal Classic fronts 6.5" = £16.00 + postage gifted on PayPal Postage is: £2.95 RM 2nd class, £3.50 RM 1st class. These can be printed to order and I will need about 48 hours before shipping. PM me for ordering. Cheers for looking! https://cimg7.ibsrv.net/gimg/www.sco...9a50de5bf1.jpg https://cimg8.ibsrv.net/gimg/www.sco...e60888ad38.jpg https://cimg6.ibsrv.net/gimg/www.sco...68536160af.jpg |
Mid week bump
|
Any pics? Interested if they defo fit a classic.
|
3 Attachment(s)
strange! There was pictures included....
The hole centres are 150mm if you measure between any two. I don't see why classics would be different from newage mind you! |
Out of interest Bazil, how do you rate those speakers? I think of Bass-Face as being budget, but are they any good?
|
Ok, but not as good as I was hoping for! They haven't been much difference over stock I don't think, which is surprising considering how much bigger they are!
|
I have one set of spacers printed and ready to ship tomorrow... :thumb:
|
Originally Posted by Bazil_SW
(Post 12033677)
Ok, but not as good as I was hoping for! They haven't been much difference over stock I don't think, which is surprising considering how much bigger they are!
|
I've got a Sony DSX-A40UI. Had that fitted before the speak swap too.
|
Originally Posted by Bazil_SW
(Post 12032499)
Hi all,
For sale, some 3D printed mounting spacers for 6.5" speakers in the front doors. Printed in PLA with 3 layers and 30% infill (nice and sturdy). With 4 captive nuts for speaker mounting. I will provide some M4 bolts also. These are required for 2 reasons when fitting aftermarket speakers to scoobs. 1) adapter for the 3 to multiple fittings 2) and most importantly (I found out the hard way!) To provide clearance for the window glass to go fully down... Shown is fitment of some Bass Face 6.5" speakers. 19mm thick, on my hawk there was no modifications to the door casing required as there is enough clearance inside, just fit and go! Fitment - confirmed: Hawk - presumed all newage as the same speakers and door casings were used on earlier models - presumed classics (assume same hole centres for the stock 3 screws. i.e. 150m if you measure centre to centre between any 2 of the mounting holes) Cost: £17.50 + postage gifted on PayPal Postage is: £2.50 RM 2nd class, £3.50 RM 1st class. These can be printed to order. PM me for ordering. Cheers for looking! https://cimg7.ibsrv.net/gimg/www.sco...9a50de5bf1.jpg https://cimg8.ibsrv.net/gimg/www.sco...e60888ad38.jpg https://cimg6.ibsrv.net/gimg/www.sco...68536160af.jpg |
Originally Posted by Russell38
(Post 12033741)
Hi would be interested in a set if you can make them for 5.25 inch
Cheers! |
Do you do the back ones as well by any chance? |
Not yet, but I was thinking of taking a look at them as they are smaller I believe, probably 4 inch as stock?
|
Originally Posted by Bazil_SW
(Post 12033910)
Not yet, but I was thinking of taking a look at them as they are smaller I believe, probably 4 inch as stock?
|
Originally Posted by Hawkins 1995
(Post 12033916)
mill today and a look on the weekend mate if you would be able to I would order a full set as the ones that come with the speaker touch the door cards haha 😂 |
I’ll take a set please mate. Measured my home made mdf spacers from a previous classic I had and they are 15cm between the 3 mounting points please pm payment details Paul |
Originally Posted by averyp2
(Post 12033964)
I’ll take a set please mate. Measured my home made mdf spacers from a previous classic I had and they are 15cm between the 3 mounting points please pm payment details Paul Can do, that for 6.5" speakers? I'm not there yet for 5.25" and rears yet. I'll drop you a pm. Cheers |
Just fitted a set perfect fit half an hour did both sides :thumb:
|
I'll take some as classic fitment has been confirmed. Pm the payment details. Thanks
|
Originally Posted by SunilWRX
(Post 12034627)
I'll take some as classic fitment has been confirmed. Pm the payment details. Thanks
|
Thanks to the help of someone on here, I now have a design for classics front doors.
Since they are a bit smaller I can do them £15 + delivery. Drop me a pm if interested. Cheers for looking! |
Are these still available ? |
Yep, printed to order! :thumb:
|
Bump
|
Received my classic adapters, thanks mate. not yet fitted but look good and include screws which is useful. Top service! cheers Paul |
Originally Posted by averyp2
(Post 12035806)
Received my classic adapters, thanks mate. not yet fitted but look good and include screws which is useful. Top service! cheers Paul |
Got a set of fronts for classics ready to ship :D
drop me a PM |
Bump
|
Bump
|
Newage rear door spacers available now too :thumb:
To fit 5 1/4" speakers £15.00 + postage |
All times are GMT +1. The time now is 12:30 AM. |
© 2024 MH Sub I, LLC dba Internet Brands