Toad ai606 alarm chirp.
#2
Scooby Regular
This should of been activated when installed there is an option to silence the chirp on arm and disarm with the fob, But the unit would of needed to be set to chirp in the first instance. The actual control unit has the main settings silent quiet and loud. It sounds like this has been set to quiet.
I would of thought that any alarm fitter would tell you were the switch is for this option, but as said it is on the control box fitted some where in the car (not the siren)
I know its not much help mate, but hopfully points you in the right direction
Mick
I would of thought that any alarm fitter would tell you were the switch is for this option, but as said it is on the control box fitted some where in the car (not the siren)
I know its not much help mate, but hopfully points you in the right direction
Mick
#3
Programming the Alarm Unit
Programming the Customer PIN Code –
The customer PIN code is a 4-digit number used to dis-arm the alarm system in an emergency, and also to
access programming mode. The factory default PIN setting is random, but each of the 4 digits can be set to
any number requested by the customer.
The customer should carefully record this PIN. If this PIN is lost,
then essential functions within the alarm will become inaccessible. This PIN code can only be reset by
returning the unit to TOAD. Ensure that the customer is fully aware of the importance of this PIN code.
To enter a 4 digit pin code; for example 4030:
Turn the
Ignition within 7 seconds, leaving it “on”.
The LED will now flash Red quickly for 3 seconds, then slows to 1 flash per second.
Count the
slow Red flashes until the 4th occurs - turn the ignition “off” immediately after the
LED extinguishes.
Turn the
ignition “on” - The LED illuminates Green, then slowly flashes Red.
Before the 1
st slow Red flash
- turn the ignition “off”.
Turn the
ignition “on” - The LED illuminates Green, then slowly flashes Red.
Count the
slow Red flashes until the 3rd occurs - turn the ignition “off” immediately after the
LED extinguishes.
Turn
the ignition “on” - The LED illuminates Green, then slowly flashes Red.
Before the 1
st slow Red flash
- turn the ignition “off”.
Note:
As shown above, a 0-digit is entered by turning the
ignition “off” immediately after the LED has finished
flashing Red quickly for 3 seconds (if it 0 is the 1
st digit of the PIN), or immediately after the LED has
illuminated Green (if it is the 2
nd, 3rd or 4th digit of the PIN). i.e. before the 1st slow Red flash occurs.
All other digits are entered by turning the
ignition “off” immediately after the LED has extinguished on the
corresponding flash number.
If the PIN code is entered correctly, the system will return to the disarm state when the ignition is switched off.
If the code is entered incorrectly then the system will stay armed and indicate a wrongly entered code by
beeping the siren 5 times.
If an incorrect PIN code is entered 3 times in succession, the alarm will block any further PIN code
attempts for 3 minutes. The PIN code block is shown by the LED giving a double flash in place of the
single flash.
IF THE OPTIONAL TOUCH KEY IS FITTED TO THE ALARM SYSTEM, THIS WILL STILL DISARM THE
ALARM SYSTEM.
Software Switch Sequence –
The alarm unit is supplied with standard default settings and features. To adjust the settings and to adjust
ultrasonic sensitivity, follow the procedure as illustrated in the example below.
To change the Siren Chirp setting (switch 1-5) from On to Off, complete the PIN code entry sequence then:
Turn the
ignition
“on”
You are
now in
switch
1-5
Press button
1, 5 times the
siren will chirp each time
the button is pressed
Press remote
button 1
once
The siren will
chirp as
confirmation
Turn the
ignition “off”
and “on"
Press button
1 once the Led will
turn
RED to show any switches
starting with the digit
1
Turn the
ignition “off”
and “on”
Press both buttons on the remote
to toggle the switch from
Off to On or On to Off
.
After adjustment, switch the ignition “off” and wait for the system to
exit programme mode indicated by a double chirp of the siren or turn
the ignition back “on” to adjust any other switches
.
#4
hi every1 wondering if anyone knows how to make the alarm chirp when activating and deactivating alarm. i would appreciate any help thanks.
#5
hi thanks for the replies guyz iv jus got back from dubai. my email is all_eyez_on_vip@hotmail.com. im hoping to get it sorted this week. the guy who installed it said that thats how they came. when i asked him why there was no chirp.
#6
if there any alarm installers in the midlands i wouldnt mind paying someone to sort it out for me as i am not too good and would like to add full closure to the system as well. i have a impreza p1. please let me know. cheers
#7
Have a similar problem with my toad, when the installer left me it chirped fine, after fiddling around with some button on the remote only, the chirp has gone and i cant get it back, surely if must be possibly to reactivate the chirp via the remote only??
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
toyney83
General Technical
10
02 October 2015 08:38 PM