Clifford alarm LED's
#1
Scooby Regular
Thread Starter
What type of LED do I need to replace the LED indicator on my alarm.
It's a Clifford concept 300!
I want to turn it clear, but flash blue
I've looked at Maplin's website and got very confused (and nearly bought a load of stuff I'll never use)
Cheers,
Iain.
(Iknow I'm a tart that's why I'm dangerous!!!)
It's a Clifford concept 300!
I want to turn it clear, but flash blue
I've looked at Maplin's website and got very confused (and nearly bought a load of stuff I'll never use)
Cheers,
Iain.
(Iknow I'm a tart that's why I'm dangerous!!!)
#2
Scooby Regular
Join Date: Jun 2002
Location: Scotland
Posts: 1,664
Likes: 0
Received 0 Likes
on
0 Posts
Any 12V LED will be a straight replacement, you just need to decide on the size and brightness. Try and get a large viewing angle as well (120deg is good) so it's still clearly visible from the sides.
If you can't get a 12V one that fits the criteria just get a normal one and use a resistor in-line with one of the pins. If you need help working this out I'll let you know how it's done.
Finally remember LEDs are polarised, they won't work if connected round the wrong way.
If you can't get a 12V one that fits the criteria just get a normal one and use a resistor in-line with one of the pins. If you need help working this out I'll let you know how it's done.
Finally remember LEDs are polarised, they won't work if connected round the wrong way.
#4
Scooby Regular
Thread Starter
Thanks Max
Is the 15 deg enough of a spread?
I was going to get rid of the Clifford bezel (No point advertising what alarm is fitted) Any sugestions on what to use?
I'll have a look at Maplins again tomorrow
Is the 15 deg enough of a spread?
I was going to get rid of the Clifford bezel (No point advertising what alarm is fitted) Any sugestions on what to use?
I'll have a look at Maplins again tomorrow
#5
No matter whether you get rid of the clifford bezel or not, use the clear cliplite bezel I mentioned as it gives a 180 degree spread from any led. You can even flush just the front of it through a 7mm hole which looks really neat and still gives a 180 degree spread due to it's freznel rings.
#6
Scooby Regular
Thread Starter
Had a quick look at Maplin. Looks like what I want!
Was going to use a JC25 (clear) 5.5volts
What is the voltage of the standard LED? Am I going to need to put a resistor in line?
Cheers
Was going to use a JC25 (clear) 5.5volts
What is the voltage of the standard LED? Am I going to need to put a resistor in line?
Cheers
Trending Topics
#8
Just use a regular LED, the necessary resistance is built into Clifford alarms as their output is specifically for running LEDs with. Don't use 5 or 12V LEDs or ones with internal resistance or flashing circuitry. The alarm takes care of everything.
#12
Dyney,
Believe me, the part numbers I gave above are the correct ones, the NR85 extreme brightness blue LED is the one to use. I've just been checking and in the last year and a half I've used over 130 of them. (I know because I've got a bundle of unused red Clifford LED's. I never throw anything away (-: ).
Just connect the anode of the NR85 to the positive purple clifford LED wire, and the cathode to the black wire. Simple as that!
Believe me, the part numbers I gave above are the correct ones, the NR85 extreme brightness blue LED is the one to use. I've just been checking and in the last year and a half I've used over 130 of them. (I know because I've got a bundle of unused red Clifford LED's. I never throw anything away (-: ).
Just connect the anode of the NR85 to the positive purple clifford LED wire, and the cathode to the black wire. Simple as that!
#13
Dyney,
Clifford have just released an "Electro Luminenescent Armed Indicator Light" from the picture it looks like it about the same size as the proximity sensor, it goes up against the front window and flashes blue!! cost about 45 squid apparently.
Be careful if you go the diy route, I wanted extra led's when I had my Clifford alarm fitted, but was told this was a no-no by the engineer because of the extra sensitive low voltage, current tampering protection circuits, so it cause fauls alarms.
Cheers, Roy.
Clifford have just released an "Electro Luminenescent Armed Indicator Light" from the picture it looks like it about the same size as the proximity sensor, it goes up against the front window and flashes blue!! cost about 45 squid apparently.
Be careful if you go the diy route, I wanted extra led's when I had my Clifford alarm fitted, but was told this was a no-no by the engineer because of the extra sensitive low voltage, current tampering protection circuits, so it cause fauls alarms.
Cheers, Roy.
#14
From Maplins, I use the NR85 15 degree 3.0cd blue led with a YH54 clear cliplite bezel, then heatshrink sleeve and glue the lot back into the clifford bezel and hey presto, a clear clifford led that flashes incredibly bright blue!
[Edited by Max the Clifford dealer - 8/11/2002 9:27:07 PM]
[Edited by Max the Clifford dealer - 8/11/2002 9:27:07 PM]
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
toyney83
General Technical
10
02 October 2015 08:38 PM
jonnyboy82
Lighting and Other Electrical
0
29 September 2015 01:59 PM