WRX BOYS - GET YOUR DYNOS OUT
#3
Scooby Regular
Thread Starter
So thats everything STI then or better
I think thats cheating
i mean to be honest, im just look for the most power without my car blowing to pieces.
I dont have loads of money kicking around but can justify a few hundred quid here and there.
I have a vf34, slightly bigger injectors i beleve - not sure what size, full decat exhaust, remap, induction, big top mount & exedy racing clutch etc.
Im currently considering:
FMIC
PORTING & WRAPPING
MAP TWEAK TO INCREASE BOOST TO 1.5 bar
i just dont want to see pistons flying through my bonnet in a cloud of smoke.
I think thats cheating
i mean to be honest, im just look for the most power without my car blowing to pieces.
I dont have loads of money kicking around but can justify a few hundred quid here and there.
I have a vf34, slightly bigger injectors i beleve - not sure what size, full decat exhaust, remap, induction, big top mount & exedy racing clutch etc.
Im currently considering:
FMIC
PORTING & WRAPPING
MAP TWEAK TO INCREASE BOOST TO 1.5 bar
i just dont want to see pistons flying through my bonnet in a cloud of smoke.
#4
Scooby Regular
iTrader: (12)
340-350 should be ok for the block, but its gearbox first.
FMIC is a waste as STI top mount is ok for circa 400bhp(so assuming yours hsuld match the STI) , porting should help it breathe along with the map tweek, if your not running a 3 port boost solinoid well worth it. Walbro fuel pump will help with the mixture too
FMIC is a waste as STI top mount is ok for circa 400bhp(so assuming yours hsuld match the STI) , porting should help it breathe along with the map tweek, if your not running a 3 port boost solinoid well worth it. Walbro fuel pump will help with the mixture too
#5
Scooby Regular
iTrader: (8)
Join Date: Jan 2006
Location: MK
Posts: 4,931
Likes: 0
Received 0 Likes
on
0 Posts
I would make it as strong as you can and do it in stages
My WRX spec
RCM Build (2.35)
RCM EJ22 Remanufactured Closed deck block
RCM Wiseco 97.5mm Forged piston
RCM WRC 14mm Stud Conversion
Block Face Skim
RCM Re-bore and plateau hone
RCM WRC 14mm head stud kit
RCM Modified Oil pump
Subaru 79MM Nitrided Crankshaft assy
RCM Extreme Uprated H section conrod
Uprated Thermostat
Cosworth Subaru Timing Belt kit
Subaru Main brg set
Mahle Motorsport Big end brg set
RCM Baffled sump
RCM Manifold
RCM Colour ceramic coating
SX Fuel pressure Regulator
RCM WRC Nimonic Exhaust Valve
RCM WRC Inlet valve
800cc Fuel Injectors
STI GPN Uprated Pitching Stopper
RCM Titanium Retainers
RCM 3" Open neck Downpipe
RCM Centre section
RCM Rear section
6 Speed Gearbox
Oil pick up pipe
Oil pick up pipe O ring
Samco Turbo Inlet Hose
Turbo inlet hose clamp
Modified inlet tumblers
RCM/Exedy Twin plate clutch & flywheel assy
Oil Cooler Modine
Cosworth air pump delete kit
RCM Parallel fuel rail kit
HF Front Mounted Intercooler
Carbon inner wing panel
RCM Mafless Induction Tube
K&N Induction Filter
Cosworth VVT Camshaft kit
Hybrid Garret RCM450 Turbo Ceramic 58mm
RCM Track Attack Oil Catch tank kit
Bosch Motorsport 10bar pump
RCM Antisurge kit
Dash 4 Aeroquip Hose
Dash 6 Aeroquip braided hose
RCM Superlite pulley set non AC
NGK Racing Spark Plug-7
Solaris ECS S6GP
Air temp sensor
RCM Carbon Cool Panel guide
Motec 4 Bar MAP Sensor
Carbon switch panel
SYVECS MAP Multi switch
https://www.scoobynet.com/828536-las...m-style-7.html
My WRX spec
RCM Build (2.35)
RCM EJ22 Remanufactured Closed deck block
RCM Wiseco 97.5mm Forged piston
RCM WRC 14mm Stud Conversion
Block Face Skim
RCM Re-bore and plateau hone
RCM WRC 14mm head stud kit
RCM Modified Oil pump
Subaru 79MM Nitrided Crankshaft assy
RCM Extreme Uprated H section conrod
Uprated Thermostat
Cosworth Subaru Timing Belt kit
Subaru Main brg set
Mahle Motorsport Big end brg set
RCM Baffled sump
RCM Manifold
RCM Colour ceramic coating
SX Fuel pressure Regulator
RCM WRC Nimonic Exhaust Valve
RCM WRC Inlet valve
800cc Fuel Injectors
STI GPN Uprated Pitching Stopper
RCM Titanium Retainers
RCM 3" Open neck Downpipe
RCM Centre section
RCM Rear section
6 Speed Gearbox
Oil pick up pipe
Oil pick up pipe O ring
Samco Turbo Inlet Hose
Turbo inlet hose clamp
Modified inlet tumblers
RCM/Exedy Twin plate clutch & flywheel assy
Oil Cooler Modine
Cosworth air pump delete kit
RCM Parallel fuel rail kit
HF Front Mounted Intercooler
Carbon inner wing panel
RCM Mafless Induction Tube
K&N Induction Filter
Cosworth VVT Camshaft kit
Hybrid Garret RCM450 Turbo Ceramic 58mm
RCM Track Attack Oil Catch tank kit
Bosch Motorsport 10bar pump
RCM Antisurge kit
Dash 4 Aeroquip Hose
Dash 6 Aeroquip braided hose
RCM Superlite pulley set non AC
NGK Racing Spark Plug-7
Solaris ECS S6GP
Air temp sensor
RCM Carbon Cool Panel guide
Motec 4 Bar MAP Sensor
Carbon switch panel
SYVECS MAP Multi switch
https://www.scoobynet.com/828536-las...m-style-7.html
#6
Scooby Regular
Thread Starter
ok, so i have no idea what a 3 port boost solinoid is & how much they are or what they do, also, can a straight forward garage fit these? the intercooler i have is bigger than the sti one so should be alright. i think i have a walbro already... thats what i was told..
The wrx is officially putting out 317bhp... would love to get nearer to 350
The wrx is officially putting out 317bhp... would love to get nearer to 350
Trending Topics
#8
Scooby Regular
iTrader: (15)
ok, so i have no idea what a 3 port boost solinoid is & how much they are or what they do, also, can a straight forward garage fit these? the intercooler i have is bigger than the sti one so should be alright. i think i have a walbro already... thats what i was told..
The wrx is officially putting out 317bhp... would love to get nearer to 350
The wrx is officially putting out 317bhp... would love to get nearer to 350
#10
Scooby Regular
Thread Starter
ok cool, next question, which boost solenoid to buy, i see perrin and turbosmart make decent ones, so what would you choose - for the best value, on ebay there are ones for 40 quid etc but i really dont want to end up chucking it and buying twice.
Spec at the moment:
VF 34 turbo
remapped
full decat and down pipe decat
jap exhaust
large top mount intercooler
Exedy racing organic clutch and flywheel
walbro i think, not 100%
larger injectors, think they are sti ones, again, not 100% as all work done before i bought it.
Engine just had £2500 spent on rebuild as the bottom end went.
its making 317bhp. wrx 2005 blob
AEM induction kit
Spec at the moment:
VF 34 turbo
remapped
full decat and down pipe decat
jap exhaust
large top mount intercooler
Exedy racing organic clutch and flywheel
walbro i think, not 100%
larger injectors, think they are sti ones, again, not 100% as all work done before i bought it.
Engine just had £2500 spent on rebuild as the bottom end went.
its making 317bhp. wrx 2005 blob
AEM induction kit
#19
Scooby Regular
Thread Starter
HAHA im on the phone to admiral now! to report your naughty ways
would it be better for me to look at larger headers rather than porting the standard wrx ones? if so can you guys recommend a set?
another question, is it easy to check if the pump is a walbro or not, is there any obvious branding & where in the engine is it located?
Will need to decide on the solinoid.
I need to choose one & also the headers, il buy a walbro if i aint got one then il go to a tuning place and have the boost turned up...
what would you buy?
would it be better for me to look at larger headers rather than porting the standard wrx ones? if so can you guys recommend a set?
another question, is it easy to check if the pump is a walbro or not, is there any obvious branding & where in the engine is it located?
Will need to decide on the solinoid.
I need to choose one & also the headers, il buy a walbro if i aint got one then il go to a tuning place and have the boost turned up...
what would you buy?
#20
Scooby Regular
iTrader: (15)
RCM headers are the best mate
Fuel pump is in the fuel tank, think there is a viewing spot under the rear seat but not sure as I didn't change mine .. lol
Sign up here mate if not already www.bbscoobys.com , lots of fellow scooby enthusiasts close to home for you
Fuel pump is in the fuel tank, think there is a viewing spot under the rear seat but not sure as I didn't change mine .. lol
Sign up here mate if not already www.bbscoobys.com , lots of fellow scooby enthusiasts close to home for you
#22
Scooby Regular
iTrader: (78)
Boosty you need to decide what your doing with the car before you venture down any mod routes. If you want it look quick and handle like a dream then dont bother with FMIC and CAI etc etc at your level. You can make a 330bhp car very quick if you listen and learn from others. Get the car sat right first, so some decent suspension upgrades inc ARB's etc, consider some better discs and pads too, and if you can afford brembo's then buy these. Keep away from gimics that offer no performance enhancements at all such as a Baileys BOV!
However again you need to decide which route your going to take with the car, I live from experience with this and with two cars I started moddifying with the intention of just makng a car quick, to wanting to track the car, HOWEVER the car in question was the wrong base car to be throwing loads of money at, and in fact at the end of power hunt in a WRX I had more money in it than what I culd have bought an STI for, but I didnt have the extras such as Brembo or a 6 Speed!!!
Rob
However again you need to decide which route your going to take with the car, I live from experience with this and with two cars I started moddifying with the intention of just makng a car quick, to wanting to track the car, HOWEVER the car in question was the wrong base car to be throwing loads of money at, and in fact at the end of power hunt in a WRX I had more money in it than what I culd have bought an STI for, but I didnt have the extras such as Brembo or a 6 Speed!!!
Rob
#24
Scooby Regular
Thread Starter
thanks for the advice rob, it does make allot of sence. i want to be realistic, i want to get to 350bhp power and then that would be the lot for the wrx. if i wanted any more, i would probably look to sell the car and go down the sti route, just being 24, my insurance wont allow the higher spec just yet. I am in the process of improving the braking, the car has strut bracing, anti roll bars all over the body & has coilovers already so thats good. Just want to know what boost solenoid and Headers will give best results for low spend. thats it really.
#26
Scooby Regular
headers your prob gonna want double that at least unless you can find some second handm even then your gonna be struggling.
i know this is prob a daft question (and maybe mentioned earlier) but you have budgeted for mapping once these mods are done?
i know this is prob a daft question (and maybe mentioned earlier) but you have budgeted for mapping once these mods are done?
#30
Scooby Regular
iTrader: (54)
i have a 2007 hawkeye wrx, running 355 bhp and its my daily driver,
vf43,sti tmic,3" d/p de-resonated centre pipe and afterburner vortex b/b
whiteline f@r arbs,droplinks,brembos,
full 6spd set up as my 5spd front diff started to whine so just went 6spd to save any probs later.
vf43,sti tmic,3" d/p de-resonated centre pipe and afterburner vortex b/b
whiteline f@r arbs,droplinks,brembos,
full 6spd set up as my 5spd front diff started to whine so just went 6spd to save any probs later.