Prosport Gauges advice needed
12 February 2011, 07:04 PM
#1
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Jan 2006
Location: MK
Posts: 4,931
Likes: 0
Received 0 Likes
on
0 Posts
Prosport Gauges advice needed
Hi guys just had my car mapped again, since the boost has been turned up it keeps setting off the warning bleep on my gauge, how do i turn this off. (long term answer is Defi but i need a fix asap 
2 hour drive home killed me)
lost the Instructions
2 hour drive home killed me) lost the Instructions
12 February 2011, 07:09 PM
#2
Scooby Regular
To reset the memory: Push and hold the button until the pointer begins to flash. Release button. Then while the pointer is still flashing (set mode) push the button and hold it to move the pointer fast or each time you push the button the pointer will move in small increments to the exact point where you want to set it. After you have the pointer where you want to set your warning level just wait about 6 seconds and the pointer will stop flashing and retain that point as your new warning level. If you pass the point you wanted to set the level at-just keep going and once it reaches the end of the scale it will begin to come back.
13 February 2011, 01:45 AM
#3
Scooby Regular
iTrader: (8)
Join Date: Feb 2008
Location: Middlesex
Posts: 2,696
Likes: 0
Received 0 Likes
on
0 Posts
13 February 2011, 02:10 AM
#4
ScoobyWorx
iTrader: (5)
Join Date: Oct 2010
Location: Barnsley SY
Posts: 768
Likes: 0
Received 0 Likes
on
0 Posts
Yes the defi gauges are the best but pro sport gauges are top quality kit for the money. And the warning you were getting was the gauge doing it's job as it was set to warn you if it over boosts. Least you knownit works. If it's the stepper motor version also very accurate too
18 February 2011, 11:41 AM
#5
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Jan 2006
Location: MK
Posts: 4,931
Likes: 0
Received 0 Likes
on
0 Posts
To reset the memory: Push and hold the button until the pointer begins to flash. Release button. Then while the pointer is still flashing (set mode) push the button and hold it to move the pointer fast or each time you push the button the pointer will move in small increments to the exact point where you want to set it. After you have the pointer where you want to set your warning level just wait about 6 seconds and the pointer will stop flashing and retain that point as your new warning level. If you pass the point you wanted to set the level at-just keep going and once it reaches the end of the scale it will begin to come back.
18 February 2011, 11:43 AM
#6
Scooby Regular
Thread Starter
iTrader: (8)
Join Date: Jan 2006
Location: MK
Posts: 4,931
Likes: 0
Received 0 Likes
on
0 Posts
Got to agree with you there especially with your build, If moneies not an object look into the electronic Defi gauges http://www.defi-shop.com/product/zdcsp/zdcsp_top.html
Now would that work with Solaris ECU ? would love shift lights.
19 February 2011, 09:20 PM
#7
Scooby Regular
Trending Topics
19 February 2011, 09:31 PM
#8
Scooby Regular
iTrader: (3)
Join Date: May 2007
Location: in the shed
Posts: 336
Likes: 0
Received 0 Likes
on
0 Posts
i have a set of these and what does my nut in is when you turn the engine off but leave the stereo on and the oil pressure gauge beeps like mad coz the engine isnt running so no oil pressure
19 February 2011, 10:44 PM
#10
Scooby Regular
iTrader: (1)
Join Date: Apr 2007
Location: Up-North Like!
Posts: 1,266
Likes: 0
Received 0 Likes
on
0 Posts
If you press and hold the peak button, turn the ignition and keep holding the peak button down until it does its sweep, this removes the beeping altogether but still allows the flashing to warn.
I had to do this with the AFR gauge as on declaration the gauge beeped all the time
Hope that helps.
Thread
Thread Starter
Forum
Replies
Last Post
robbie1988
Wanted
2
13 September 2015 09:25 AM
Scooby-Doo 2
Wheels And Tyres For Sale
1
09 September 2015 06:51 PM
