Intercooler hose size
#1
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Aug 2010
Location: Manchester
Posts: 641
Likes: 0
Received 0 Likes
on
0 Posts
Intercooler hose size
Can anyone tell the internal size of this intercooler hose please and whats the best boost clamps to use for this job
http://www.ebay.co.uk/itm/2-75-T-Bol...item4adad5f542
And are these boost clamps ok or a bit over the top
http://www.ebay.co.uk/itm/2-75-T-Bol...item4adad5f542
And are these boost clamps ok or a bit over the top
#3
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Aug 2010
Location: Manchester
Posts: 641
Likes: 0
Received 0 Likes
on
0 Posts
Did you buy a whole kit then with the Y pipe?.Whats confusing is there is a good few couplers on ebay with sizes ranging from 57mm up to 102mm for the Subaru I thought the intercooler to throttle body hose was the same size as other models
#4
Scooby Regular
iTrader: (4)
have a quick look at me build thread to see what i bought in the mishimoto kit.
https://www.scoobynet.com/1009543-th...freshed-3.html
The only reason i know it is 80 mm(on the newage TMIC) is because i was going to replace just that hose. But when a brand new kit (inc Y hoses) for £10 unopened i had to jump at the chance.
If in doubt take it off and measure it.
https://www.scoobynet.com/1009543-th...freshed-3.html
The only reason i know it is 80 mm(on the newage TMIC) is because i was going to replace just that hose. But when a brand new kit (inc Y hoses) for £10 unopened i had to jump at the chance.
If in doubt take it off and measure it.
#5
Scooby Regular
iTrader: (7)
Join Date: Dec 2009
Location: Surrey
Posts: 2,008
Likes: 0
Received 0 Likes
on
0 Posts
If it's the throttle body hose you're looking at samco do two of them. One is known as an extreme and a lot shorter.
They're between £10 - £15 and you can get the both from merlin motorsport based as castle coombe. But both as all fmic are differently shaped and send one back after you've had a test fit.
They're between £10 - £15 and you can get the both from merlin motorsport based as castle coombe. But both as all fmic are differently shaped and send one back after you've had a test fit.
#7
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Aug 2010
Location: Manchester
Posts: 641
Likes: 0
Received 0 Likes
on
0 Posts
Im after some clamps like these in the links that are gonna clamp a 80mm hose well enough.i carnt seem to find the size close enough.The 79mm-87mm just seem to small.Does anyone know where I can get a bigger size say 75mm-85mm-87mm even.
http://www.ebay.co.uk/itm/2x-3-79mm-...3D131279492255
http://www.ebay.co.uk/itm/2x-3-79mm-...3D131279492255
Trending Topics
#8
Scooby Regular
iTrader: (7)
Join Date: Dec 2009
Location: Surrey
Posts: 2,008
Likes: 0
Received 0 Likes
on
0 Posts
Rik. Yes, it's the length that differs. As for the request above give merlin a call. They also do the solid joiner pipes as well.
If not, bob@aztec, Alyn as performance or advanced automotives in Bristol
If not, bob@aztec, Alyn as performance or advanced automotives in Bristol
Thread
Thread Starter
Forum
Replies
Last Post
Flat4x4-again
General Technical
2
29 September 2015 06:32 PM