My wrx sti 2015
#1
Scooby Regular
Thread Starter
My wrx sti 2015
My build nealy done
2.2 CDB
nitrided crankshaft
race bearings.
Carrillo rods..
Marle power pack pistons.
machining.
ARP head studs.
Gasket and seal kit.
oil pump high flow..
spec "C" heads.
stainless valves.
supertec springs/retainers.
uprated head gaskets.
rotated pipe work kit..
GT spec headers.
header wrap.
GT 30 R billet turbocharger.
External waste gate.
stainless exhaust system..
inlet system & cone filter....
Perrin FMIC kit.
perrin oil cooler.
GFB dump valve.
syvecs ecu .
can bus interface.
uprated bosch fuel pump.
oil temp/pressure sensor.
twin plate exedy clutch.
fly by wire interface..
wiring loom adaptor..
fuel pump wiring and relay.
anti lag and launch control
AND SOME MORE TO BE ADDED
2.2 CDB
nitrided crankshaft
race bearings.
Carrillo rods..
Marle power pack pistons.
machining.
ARP head studs.
Gasket and seal kit.
oil pump high flow..
spec "C" heads.
stainless valves.
supertec springs/retainers.
uprated head gaskets.
rotated pipe work kit..
GT spec headers.
header wrap.
GT 30 R billet turbocharger.
External waste gate.
stainless exhaust system..
inlet system & cone filter....
Perrin FMIC kit.
perrin oil cooler.
GFB dump valve.
syvecs ecu .
can bus interface.
uprated bosch fuel pump.
oil temp/pressure sensor.
twin plate exedy clutch.
fly by wire interface..
wiring loom adaptor..
fuel pump wiring and relay.
anti lag and launch control
AND SOME MORE TO BE ADDED
Last edited by Wigan WRX STI Fan; 25 May 2015 at 09:34 PM.
#7
Scooby Regular
Trending Topics
#8
Scooby Regular
Thread Starter
2.2 CDB
nitrided crankshaft
race bearings.
Carrillo rods..
Marle power pack pistons.
machining.
ARP head studs.
Gasket and seal kit.
oil pump high flow..
spec "C" heads.
stainless valves.
supertec springs/retainers.
uprated head gaskets.
rotated pipe work kit..
GT spec headers.
header wrap.
GT 30 R billet turbocharger.
External waste gate.
stainless exhaust system..
inlet system & cone filter....
Perrin FMIC kit.
perrin oil cooler.
GFB dump valve.
syvecs ecu .
can bus interface.
uprated bosch fuel pump.
oil temp/pressure sensor.
twin plate exedy clutch.
fly by wire interface..
wiring loom adaptor..
fuel pump wiring and relay.
AND SOME MORE TO BE ADDED
nitrided crankshaft
race bearings.
Carrillo rods..
Marle power pack pistons.
machining.
ARP head studs.
Gasket and seal kit.
oil pump high flow..
spec "C" heads.
stainless valves.
supertec springs/retainers.
uprated head gaskets.
rotated pipe work kit..
GT spec headers.
header wrap.
GT 30 R billet turbocharger.
External waste gate.
stainless exhaust system..
inlet system & cone filter....
Perrin FMIC kit.
perrin oil cooler.
GFB dump valve.
syvecs ecu .
can bus interface.
uprated bosch fuel pump.
oil temp/pressure sensor.
twin plate exedy clutch.
fly by wire interface..
wiring loom adaptor..
fuel pump wiring and relay.
AND SOME MORE TO BE ADDED
#11
Scooby Regular
at the min 0 haha, engines in bits. New engine will be closed deck 2.1 build. power wise will prob be mid 300's to start with while bank balance recovers, then will get 6 speed box and supporting mods and eventually pushed to 500 ish.
Had a dark blue classic for ten years which was a long term project and this will be a similar sort of thing. Engine was on the list to do but not yet, untill crank started rattling and it got brought forward.
Had a dark blue classic for ten years which was a long term project and this will be a similar sort of thing. Engine was on the list to do but not yet, untill crank started rattling and it got brought forward.
Thread
Thread Starter
Forum
Replies
Last Post
KOEScoob
ScoobyNet General
6
17 September 2015 03:51 PM