autogauge help needed
#1
Scooby Regular
Thread Starter
Join Date: Sep 2006
Location: belfast
Posts: 47
Likes: 0
Received 0 Likes
on
0 Posts
autogauge help needed
anyone got instructions or manuals on how to install these gauges ,i have boost gauge ,oil temp gauge and oil pressure gauge ...any help would be greatly appreciated..
#2
Scooby Regular
iTrader: (2)
Originally Posted by Paca
anyone got instructions or manuals on how to install these gauges ,i have boost gauge ,oil temp gauge and oil pressure gauge ...any help would be greatly appreciated..
chiark hub.home
Alcazar
Trending Topics
#9
Scooby Regular
iTrader: (2)
Originally Posted by Matt_taylor
its a 97 P UK turbo
can i run one strait from the battery? But then wouldnt it light up all the time?
can i run one strait from the battery? But then wouldnt it light up all the time?
You need to know which YOUR gauges need, (just to help you here, Defi's need BOTH ).
There's nowt to stop you taking a permanent live direct from the battery, but it MUST, repeat MUST, have a suitable fuse in between the battery and the gauges, pref close to the battery! If it's for gauges, 5A will be OK.
Most people like to pick up lives inside the car, as they are already fused
HTH,
Alcazar
BTW: lives, don't normally light up gauges. That's normally a feed taken from sidelights/dashlights etc. The Live feed is to POWER the gauge. Which do you need to do?
#11
Scooby Regular
iTrader: (2)
Originally Posted by Matt_taylor
i just have a little bulb inthe back which lights the back up...
my mate has one he said he took out the cigar lighter and used that??
gonna go have a look in a mo
my mate has one he said he took out the cigar lighter and used that??
gonna go have a look in a mo
Alcazar
#12
Done it! and its gone strait to the battery.. when i picked up the wiring, fuses and everything they said it will be fine if its not all the time as its only the smallest ever LED.. sowill be the same as my alarm light,
#14
Scooby Regular
iTrader: (2)
Originally Posted by Matt_taylor
Done it! and its gone strait to the battery.. when i picked up the wiring, fuses and everything they said it will be fine if its not all the time as its only the smallest ever LED.. sowill be the same as my alarm light,
Alcazar
#16
Originally Posted by alcazar
But you HAVE fused it, haven't you?
Alcazar
Alcazar
sure have, 5amp fuse as u said before mate, put it about 8" where it joins the battery..
where are u paca? if u were close i would come roundand show u how to wire it and where to plug in the boost gauge
#17
Scooby Regular
Join Date: Mar 2006
Location: Yorkshire
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
just in case anyone else is looking for help on this subject
sorry mate, just got your PM! have you installed the senders for the oil temperature and pressure? i had a sandwich plate (from ebay about £12) which fits between the oil filter and sump, makes life a shed load easier to fit, there is a site (think it may have closed down now!) which showed you the subaru blanking plugs where you can connect them, but they looked like a hell of a ball ache, taking belts off and the like. i took the boost pipe off the pipe out of the end of my dump valve with a t-connector i had (mines an aftermarket dump valve). for the gauge wiring, the reds are a permanent live, the oranges are illumination, the greens are sensor wires and the blacks are neutral. wired all the blacks together and to an earth point (anywhere on the body) i wired all the reds and oranges together (because i have smoked gauges they nedded to be lit up all the time to see them!) and wired them to the cable coming off the ignition barrel that powers your dials up (if you put a tester between the bodywork and the cables an see which one goes live when the ignition is on the second click) the green from the oil pressure to the cable from the oil pressure sender, and the oil temp green to the cable from the oil temp sender. the boost pipe goes straight onto the gauge. hope this helps mate, if not drop us a message. andy
sorry mate, just got your PM! have you installed the senders for the oil temperature and pressure? i had a sandwich plate (from ebay about £12) which fits between the oil filter and sump, makes life a shed load easier to fit, there is a site (think it may have closed down now!) which showed you the subaru blanking plugs where you can connect them, but they looked like a hell of a ball ache, taking belts off and the like. i took the boost pipe off the pipe out of the end of my dump valve with a t-connector i had (mines an aftermarket dump valve). for the gauge wiring, the reds are a permanent live, the oranges are illumination, the greens are sensor wires and the blacks are neutral. wired all the blacks together and to an earth point (anywhere on the body) i wired all the reds and oranges together (because i have smoked gauges they nedded to be lit up all the time to see them!) and wired them to the cable coming off the ignition barrel that powers your dials up (if you put a tester between the bodywork and the cables an see which one goes live when the ignition is on the second click) the green from the oil pressure to the cable from the oil pressure sender, and the oil temp green to the cable from the oil temp sender. the boost pipe goes straight onto the gauge. hope this helps mate, if not drop us a message. andy
Thread
Thread Starter
Forum
Replies
Last Post
MH-Racing
Subaru Parts
18
18 October 2015 04:49 PM
robbie1988
Wanted
2
13 September 2015 09:25 AM
Scooby-Doo 2
Wheels And Tyres For Sale
1
09 September 2015 06:51 PM