Adjusting Arming & Disarming beep?
#1
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Jul 2011
Location: England
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
Adjusting Arming & Disarming beep?
OK i have seen a few posts on this and noticed people mentioning keypad, what keypad are they reffering to? What are the steps for adjusting or turning off the arming beeps on a 54 wrx sti?
#2
Scooby Regular
iTrader: (14)
Join Date: Aug 2009
Location: Worcs.
Posts: 2,396
Likes: 0
Received 0 Likes
on
0 Posts
Right hand side dash - just below the level of the st. wheel.. a draw pulls down where there is a key pad inside.
Dont know many codes, look in your manual if u have one, or im sure pips on here can help out.
Dont know many codes, look in your manual if u have one, or im sure pips on here can help out.
#3
Scooby Regular
Thread Starter
iTrader: (1)
Join Date: Jul 2011
Location: England
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
Found the answer to my question:
The following features are switch able by the end user, using the keypad, and are detailed in the back of your
operating instructions.
To access this mode - turn on the vehicle ignition, press the remote button once, type one of the numbers
listed in the chart below, immediately turn off the ignition. The numbers will have the following effect:
Number Function
0 Last trigger isolation - allows the system to be set excluding any circuit giving a trigger signal
at the end of the settle time (i.e. allows the system to be set with a defective bonnet switch,
without “false alarming” until the switch can be replaced)
1 Turns off the bleeps only for the next time the system is armed (If bleeps turned on!)
2 Turn off ultrasonics only for the next time the system is armed (also possible by pressing the
Remote Key with the ignition on before arming)
3 Puts the system into valet mode (effectively freezing the passive immobilisation and any
other features such as auto arm when the vehicle goes in for service. System re-activated by
arming with the remote key).
4 Turn on auto-lock (an anti-hijack feature that locks the doors and boot when the ignition is
turned on)
5 Turn off auto-lock
6 Turn off bleeps every time system is armed or disarmed
(Turned off at manufacture to comply with legislation)
7 Turn on bleeps every time system is armed or disarmed
( Note: This will contravene current legislation)
8 Displays vehicle’s battery voltage – 10 flashes on dashboard LED = approximately 10 volts
9 Turn on super-lock for next set period (allows the alarm to arm, but then shuts down the
receiver. This reduces the systems current consumption if the vehicle is left for a number of
weeks. The system then can only be disarmed using your PIN number , this gives protection
even if your keys are stolen, whilst you are away on holiday.* Toggles between loud and soft arming/disarming bleeps if selected ( See above note in 7)
Programming a New PIN Code:
The standard PIN code can be changed following the sequence below:
i) Type in to the keypad **
ii) Type in to the keypad the “existing PIN code” then *
iii) Type in to the keypad 92 * “new PIN code” * “new PIN code” #
Programming Remote Keys to the System:
Remote keys can be added or removed to/from the system following the sequence below:
i) Type in to the keypad **
ii) Type in to the keypad the “existing PIN code” then *
iii) Type in to the keypad 91 * “ the number of keys to be used” #
iv) Press the first remote key button until bleep sounds, release and press next key. Continue until all
keys have been taught to the system. Note the maximum number of keys is 4 and all keys required
to operate the system must be taught during this operation - any key not included will no longer
operate the system.
The following features are switch able by the end user, using the keypad, and are detailed in the back of your
operating instructions.
To access this mode - turn on the vehicle ignition, press the remote button once, type one of the numbers
listed in the chart below, immediately turn off the ignition. The numbers will have the following effect:
Number Function
0 Last trigger isolation - allows the system to be set excluding any circuit giving a trigger signal
at the end of the settle time (i.e. allows the system to be set with a defective bonnet switch,
without “false alarming” until the switch can be replaced)
1 Turns off the bleeps only for the next time the system is armed (If bleeps turned on!)
2 Turn off ultrasonics only for the next time the system is armed (also possible by pressing the
Remote Key with the ignition on before arming)
3 Puts the system into valet mode (effectively freezing the passive immobilisation and any
other features such as auto arm when the vehicle goes in for service. System re-activated by
arming with the remote key).
4 Turn on auto-lock (an anti-hijack feature that locks the doors and boot when the ignition is
turned on)
5 Turn off auto-lock
6 Turn off bleeps every time system is armed or disarmed
(Turned off at manufacture to comply with legislation)
7 Turn on bleeps every time system is armed or disarmed
( Note: This will contravene current legislation)
8 Displays vehicle’s battery voltage – 10 flashes on dashboard LED = approximately 10 volts
9 Turn on super-lock for next set period (allows the alarm to arm, but then shuts down the
receiver. This reduces the systems current consumption if the vehicle is left for a number of
weeks. The system then can only be disarmed using your PIN number , this gives protection
even if your keys are stolen, whilst you are away on holiday.* Toggles between loud and soft arming/disarming bleeps if selected ( See above note in 7)
Programming a New PIN Code:
The standard PIN code can be changed following the sequence below:
i) Type in to the keypad **
ii) Type in to the keypad the “existing PIN code” then *
iii) Type in to the keypad 92 * “new PIN code” * “new PIN code” #
Programming Remote Keys to the System:
Remote keys can be added or removed to/from the system following the sequence below:
i) Type in to the keypad **
ii) Type in to the keypad the “existing PIN code” then *
iii) Type in to the keypad 91 * “ the number of keys to be used” #
iv) Press the first remote key button until bleep sounds, release and press next key. Continue until all
keys have been taught to the system. Note the maximum number of keys is 4 and all keys required
to operate the system must be taught during this operation - any key not included will no longer
operate the system.
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
28
28 December 2015 11:07 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM