Notices
General Technical
Sponsored by:
Sponsored by: CARiD

MAF ADVISE PLEASE!

Old Feb 20, 2010 | 03:51 PM
  #1  
magneel1's Avatar
magneel1
Thread Starter
Scooby Regular
iTrader: (18)
 
Joined: Jan 2010
Posts: 1,179
Likes: 0
From: London
Default MAF ADVISE PLEASE!

Hi I am quite new with Subaru's so needed some help.
I have been advised to get a new MAF for MY00 UK WRX.

Car has an EJ257 engine with loads of mods.
Was wondering if all MAF's are the same or would I need an uprated one or
something different as the car is not standard...

Please advise further.


Thanks

Neel
Reply
Old Feb 20, 2010 | 04:23 PM
  #2  
Scooby715's Avatar
Scooby715
Scooby Regular
 
Joined: Oct 2008
Posts: 58
Likes: 0
From: huddersfield
Default

why are you putting a new maf sensor on it? is it running lumpy, engine management light on, it won't run, or all of the above!!?? also what mod's ya got??
Reply
Old Feb 20, 2010 | 05:09 PM
  #3  
magneel1's Avatar
magneel1
Thread Starter
Scooby Regular
iTrader: (18)
 
Joined: Jan 2010
Posts: 1,179
Likes: 0
From: London
Default

Car cuts out sometimes so advised to replace MAF, Engine management light not on..

Following mods:


EJ257 STI 2.5 BOTTOM END

V4 STI HEADS

STI 8 RUNNING GEAR

ACL RACE BEARINGS

FORGED PISTONS

550CC INJECTORS

FUEL PRESSURE REGULATOR -AEROMOTIVE WITH GAUGE

WALBRO FUEL PUMP 255L

APEXI POWER FC AND COMMANDER ECU

APEXI AVIC-R BOOST CONTROLLER

JGM REMAP


NEEL

Last edited by magneel1; Feb 20, 2010 at 05:10 PM.
Reply
Old Feb 20, 2010 | 05:53 PM
  #4  
WhiteWagonMan's Avatar
WhiteWagonMan
Scooby Regular
iTrader: (34)
 
Joined: Apr 2009
Posts: 1,419
Likes: 0
From: Trying to pull a 10 second 1/4 mile running a standard 2.0ltr engine...
Default

Get it to a garage who has the select monitor so it can be read for a more accurate cause of the problem,car cuts out sometimes so replace the maf is not a good way to start solving the problem,and not good advice,get it checked properly as maf failure WILL bring up the cel.
Reply
Old Feb 20, 2010 | 09:15 PM
  #5  
magneel1's Avatar
magneel1
Thread Starter
Scooby Regular
iTrader: (18)
 
Joined: Jan 2010
Posts: 1,179
Likes: 0
From: London
Default

Where's best place to get it checked.
I'm located in Middlesex..

Thanks
Reply
Old Feb 20, 2010 | 09:32 PM
  #6  
joz8968's Avatar
joz8968
Scooby Regular
15 Year Member
iTrader: (13)
 
Joined: Aug 2006
Posts: 23,764
Likes: 9
From: Leicester
Default

Power Engineeering are in Middlesex. Don't know what their rep is like on Scoobs though (they morphed into the Scoob scene after being Ford tuners in the 90s)...
Reply
Old Feb 20, 2010 | 10:24 PM
  #7  
Jolly Green Monster's Avatar
Jolly Green Monster
Former Sponsor
iTrader: (4)
 
Joined: Jan 2001
Posts: 16,548
Likes: 2
From: ECU Mapping - www.JollyGreenMonster.co.uk
Default

you can check the maf on the commander.. under monitor select the "airflow" parameter..

with ignition on and engine off it should be between 1000 and 1060mv.. if it is higher then the maf needs replacing..

If that is okay then I can check all is okay with the map or if anything else at issue..
lambda sensor for example, or stepper motor. I presume you bought the car already done?

Simon
Reply

Trending Topics

Old Feb 20, 2010 | 10:31 PM
  #8  
magneel1's Avatar
magneel1
Thread Starter
Scooby Regular
iTrader: (18)
 
Joined: Jan 2010
Posts: 1,179
Likes: 0
From: London
Default

Thanks Simon I'll have a look into that tomorrow...
Yes got it all already done.

Neel
Reply
Old Feb 20, 2010 | 11:01 PM
  #9  
joz8968's Avatar
joz8968
Scooby Regular
15 Year Member
iTrader: (13)
 
Joined: Aug 2006
Posts: 23,764
Likes: 9
From: Leicester
Default

Sorry magneel, I overlooked that you had a PFC/Commander - I would have advised checking the Commander too, etc.

But sharp Simon to the rescue..... as always. "Simon says..."

Last edited by joz8968; Feb 20, 2010 at 11:02 PM.
Reply
Old Feb 20, 2010 | 11:09 PM
  #10  
Jolly Green Monster's Avatar
Jolly Green Monster
Former Sponsor
iTrader: (4)
 
Joined: Jan 2001
Posts: 16,548
Likes: 2
From: ECU Mapping - www.JollyGreenMonster.co.uk
Default

Originally Posted by magneel1
Thanks Simon I'll have a look into that tomorrow...
Yes got it all already done.

Neel
more than happy to check it.. let me know how you get on

Simon
Reply
Old Feb 21, 2010 | 01:02 PM
  #11  
magneel1's Avatar
magneel1
Thread Starter
Scooby Regular
iTrader: (18)
 
Joined: Jan 2010
Posts: 1,179
Likes: 0
From: London
Default

Getting my car back today or tomorrow from mechanic.
Ill let you know how I get on.

Thanks for the help.

Neel
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Darrell@Scoobyworx
Trader Announcements
26
Jan 30, 2024 01:27 PM
SilverM3
ScoobyNet General
8
Feb 24, 2021 01:03 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
Nov 18, 2015 07:03 AM
buckerz69
Wanted
2
Oct 3, 2015 09:55 PM
bluebullet29
General Technical
2
Sep 27, 2015 07:52 PM


Thread Tools
Search this Thread

All times are GMT +1. The time now is 09:12 AM.