MAF ADVISE PLEASE!
Hi I am quite new with Subaru's so needed some help.
I have been advised to get a new MAF for MY00 UK WRX.
Car has an EJ257 engine with loads of mods.
Was wondering if all MAF's are the same or would I need an uprated one or
something different as the car is not standard...
Please advise further.
Thanks
Neel
I have been advised to get a new MAF for MY00 UK WRX.
Car has an EJ257 engine with loads of mods.
Was wondering if all MAF's are the same or would I need an uprated one or
something different as the car is not standard...
Please advise further.
Thanks
Neel
Car cuts out sometimes so advised to replace MAF, Engine management light not on..
Following mods:
EJ257 STI 2.5 BOTTOM END
V4 STI HEADS
STI 8 RUNNING GEAR
ACL RACE BEARINGS
FORGED PISTONS
550CC INJECTORS
FUEL PRESSURE REGULATOR -AEROMOTIVE WITH GAUGE
WALBRO FUEL PUMP 255L
APEXI POWER FC AND COMMANDER ECU
APEXI AVIC-R BOOST CONTROLLER
JGM REMAP
NEEL
Following mods:
EJ257 STI 2.5 BOTTOM END
V4 STI HEADS
STI 8 RUNNING GEAR
ACL RACE BEARINGS
FORGED PISTONS
550CC INJECTORS
FUEL PRESSURE REGULATOR -AEROMOTIVE WITH GAUGE
WALBRO FUEL PUMP 255L
APEXI POWER FC AND COMMANDER ECU
APEXI AVIC-R BOOST CONTROLLER
JGM REMAP
NEEL
Last edited by magneel1; Feb 20, 2010 at 05:10 PM.
Scooby Regular
iTrader: (34)
Joined: Apr 2009
Posts: 1,419
Likes: 0
From: Trying to pull a 10 second 1/4 mile running a standard 2.0ltr engine...
Get it to a garage who has the select monitor so it can be read for a more accurate cause of the problem,car cuts out sometimes so replace the maf is not a good way to start solving the problem,and not good advice,get it checked properly as maf failure WILL bring up the cel.
Former Sponsor
iTrader: (4)
Joined: Jan 2001
Posts: 16,548
Likes: 2
From: ECU Mapping - www.JollyGreenMonster.co.uk
you can check the maf on the commander.. under monitor select the "airflow" parameter..
with ignition on and engine off it should be between 1000 and 1060mv.. if it is higher then the maf needs replacing..
If that is okay then I can check all is okay with the map or if anything else at issue..
lambda sensor for example, or stepper motor. I presume you bought the car already done?
Simon
with ignition on and engine off it should be between 1000 and 1060mv.. if it is higher then the maf needs replacing..
If that is okay then I can check all is okay with the map or if anything else at issue..
lambda sensor for example, or stepper motor. I presume you bought the car already done?
Simon
Trending Topics
Sorry magneel, I overlooked that you had a PFC/Commander - I would have advised checking the Commander too, etc.
But sharp Simon to the rescue..... as always. "Simon says..."
But sharp Simon to the rescue..... as always. "Simon says..."
Last edited by joz8968; Feb 20, 2010 at 11:02 PM.
Former Sponsor
iTrader: (4)
Joined: Jan 2001
Posts: 16,548
Likes: 2
From: ECU Mapping - www.JollyGreenMonster.co.uk
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
Nov 18, 2015 07:03 AM




