post 96 map sensor fitment to 95 wrx
#1
Scooby Regular
Thread Starter
iTrader: (14)
Join Date: May 2006
Location: Sunderland
Posts: 533
Likes: 0
Received 0 Likes
on
0 Posts
post 96 map sensor fitment to 95 wrx
I'm getting ready to get the car ready to fit a Simtek ecu. As advised i've bought a post 96 Map sensor (off a 99 RB5),so i can spool above 1.2bar, thought it would be straight swap but i need to splice the wires from the new Map sensor to the wiring on the old harness (a 94 wrx). But the thing is there different colours.
New Map wires
Yellow/Black stripe
Black/white stripe
Blue
old Map wires
White
Pink
Green
Anyone any ideas which wire goes to which
Any help would be greatly appreciated.
New Map wires
Yellow/Black stripe
Black/white stripe
Blue
old Map wires
White
Pink
Green
Anyone any ideas which wire goes to which
Any help would be greatly appreciated.
#2
Former Sponsor
Join Date: Dec 2005
Location: 10.68 QT mile in 2007 2.33 Type R ** Current 2002 Spec C 2.33 Track prepped.
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
MY92-96 MAP sensor Wiring
Red = +12V
White = Sensor
Green = Gnd
MY97-00 MAP sensor
Looking at connector with pressure pipe facing down
Left = +12v
Center = Signal
Right = Gnd
Pin Numbers Wire colours:
1 = Blue
2 = Yellow-Black
3 = Red
Red = +12V
White = Sensor
Green = Gnd
MY97-00 MAP sensor
Looking at connector with pressure pipe facing down
Left = +12v
Center = Signal
Right = Gnd
Pin Numbers Wire colours:
1 = Blue
2 = Yellow-Black
3 = Red
#3
Scooby Regular
Thread Starter
iTrader: (14)
Join Date: May 2006
Location: Sunderland
Posts: 533
Likes: 0
Received 0 Likes
on
0 Posts
Pin Numbers Wire colours:
1 = Blue
2 = Yellow-Black
3 = Red the third wire on the new Map sensor is black whith white strip not red, it this the same wire ?.
Cheers
Mark.
1 = Blue
2 = Yellow-Black
3 = Red the third wire on the new Map sensor is black whith white strip not red, it this the same wire ?.
Cheers
Mark.
#5
Former Sponsor
Join Date: Dec 2005
Location: 10.68 QT mile in 2007 2.33 Type R ** Current 2002 Spec C 2.33 Track prepped.
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
Your existing wiring
Red = +12V
White = Sensor
Green = Gnd
With the New map sensor Connector facing you with pressure pipe facing down, connect as follows, forget about the existing wire colour on your new map connect according to location.
Connect old wiring as follows.
Left = +12v = Red
Center = Signal = White
Right = Gnd = Ground
If you have it wrong, it will throw a cell.
Red = +12V
White = Sensor
Green = Gnd
With the New map sensor Connector facing you with pressure pipe facing down, connect as follows, forget about the existing wire colour on your new map connect according to location.
Connect old wiring as follows.
Left = +12v = Red
Center = Signal = White
Right = Gnd = Ground
If you have it wrong, it will throw a cell.
Thread
Thread Starter
Forum
Replies
Last Post
Scott@ScoobySpares
Full Cars Breaking For Spares
61
11 January 2021 03:08 PM
Mattybr5@MB Developments
Full Cars Breaking For Spares
33
29 August 2017 07:18 PM
Scott@ScoobySpares
Full Cars Breaking For Spares
7
14 December 2015 08:16 AM