exhaust question
#1
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2008
Location: Norwich
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
exhaust question
hello all
i've purchased a milltek downpipe 3'' bore and it has a flat flange where it joins to the centre section which is a problem because the cobra 3'' centre section i have has a flange and then it opens a bit further to allow for the standard donut gasket?
does anyone know any centre sections with a flat flange that will mate up to the milltek downpipe?? and i'll send the cobra centre back
cheers Jim
i've purchased a milltek downpipe 3'' bore and it has a flat flange where it joins to the centre section which is a problem because the cobra 3'' centre section i have has a flange and then it opens a bit further to allow for the standard donut gasket?
does anyone know any centre sections with a flat flange that will mate up to the milltek downpipe?? and i'll send the cobra centre back
cheers Jim
#2
Scooby Regular
Join Date: Jul 2008
Location: se london
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
hello all
i've purchased a milltek downpipe 3'' bore and it has a flat flange where it joins to the centre section which is a problem because the cobra 3'' centre section i have has a flange and then it opens a bit further to allow for the standard donut gasket?
does anyone know any centre sections with a flat flange that will mate up to the milltek downpipe?? and i'll send the cobra centre back
cheers Jim
i've purchased a milltek downpipe 3'' bore and it has a flat flange where it joins to the centre section which is a problem because the cobra 3'' centre section i have has a flange and then it opens a bit further to allow for the standard donut gasket?
does anyone know any centre sections with a flat flange that will mate up to the milltek downpipe?? and i'll send the cobra centre back
cheers Jim
#4
Scooby Regular
Join Date: Jul 2008
Location: se london
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
hope you sort it mate you cant beat the sound of a nicely set up scooby
#5
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2008
Location: Norwich
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
jim seriously mate have you tried to get any info on the centre section as when i was enquring about a set up for my classic they appear to sell both - non resonated and resonated centre section place i was looking at was in essex i'll try and pm you the address
hope you sort it mate you cant beat the sound of a nicely set up scooby
hope you sort it mate you cant beat the sound of a nicely set up scooby
i'll have a proper look around tomorrow, just been scanning the internet whilst talking to the family today
if you could PM me it though, that would be great thanks
#6
Scooby Regular
Join Date: Jul 2008
Location: se london
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#8
Scooby Regular
iTrader: (13)
Jim, if your downpipe has a genuine 3" bore at the centre-section flange end, then I'm certain you can just mate it up to the centre-section's flange - assuming it's a normal 'blunderbuss's bowl'-like one with the 'loose' free flange - using a flat 'diamond' shaped gasket (instead of the normal donut gasket).
The flange bolt holes should be elongated on the centre-section flange, so as to be able to fit the wider pitched holes on the downpipe's flange.
You'll need a larger 3" diamond gasket to fit though (instead of the normal 2.5" one). Cobra themselves do their own (see 2nd item from bottom): ExhaustsUK: Suppliers of Cobra Sport Performance Exhausts
Or RCM: Roger Clark Motorsport - RCM Product Detail
Or eBay: http://cgi.ebay.co.uk/Hks-Exhaust-Gasket-76mm-3-inch-ID-for-Subaru-Impreza_W0QQitemZ260334079631QQcmdZViewItemQQptZUK _CarsParts_Vehicles_CarParts_SM?hash=item260334079 631&_trksid=p3286.c0.m14&_trkparms=72%3A1299|66%3A 2|65%3A12|39%3A1|240%3A1318
The flange bolt holes should be elongated on the centre-section flange, so as to be able to fit the wider pitched holes on the downpipe's flange.
You'll need a larger 3" diamond gasket to fit though (instead of the normal 2.5" one). Cobra themselves do their own (see 2nd item from bottom): ExhaustsUK: Suppliers of Cobra Sport Performance Exhausts
Or RCM: Roger Clark Motorsport - RCM Product Detail
Or eBay: http://cgi.ebay.co.uk/Hks-Exhaust-Gasket-76mm-3-inch-ID-for-Subaru-Impreza_W0QQitemZ260334079631QQcmdZViewItemQQptZUK _CarsParts_Vehicles_CarParts_SM?hash=item260334079 631&_trksid=p3286.c0.m14&_trkparms=72%3A1299|66%3A 2|65%3A12|39%3A1|240%3A1318
Last edited by joz8968; 26 December 2008 at 10:33 AM.
#9
Scooby Regular
Thread Starter
iTrader: (3)
Join Date: Dec 2008
Location: Norwich
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
hi joz, the problem is this centre section has a flare thats bigger than 3'' after the flange which is actually welded in place. i held the flared piece up to my standard downpipe and it fits perfectly over the donut gasket but because now i've got the flat flange on the milltek it won't butt up
#10
Scooby Regular
iTrader: (13)
The two flanges aren't supposed to make contact, if that's what you mean. The donut sits proud by about half an inch (although may be less because of your larger bowl?) and is designed to act like a universal joint, so that the system can easily sit in place without any unwanted tension to it. See here...
That's why there are those 'take-up' springs for the bolts - they can be tightened to a lesser or greater degree to help fine-tune the postion...
That's why there are those 'take-up' springs for the bolts - they can be tightened to a lesser or greater degree to help fine-tune the postion...
Last edited by joz8968; 26 December 2008 at 11:46 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Brzoza
Engine Management and ECU Remapping
1
02 October 2015 05:26 PM