turbo and mapping?
#1
turbo and mapping?
what turbo do i need to use to obtain 380-400hp an a 2003 uk sti?
what other mods will i need to obtain these figures?
will a ecutek map cope with these mods?
what other mods will i need to obtain these figures?
will a ecutek map cope with these mods?
#2
anyone?
been doing some hunting on the net and found a andy forest 20g td05???
full 3" exhaust system
uprated boost control solinoid or ebc
uprated fuel pump
anything else??? will turbo fit directly onto std flange, intake and oil feeds ect???
seen somewhere that 00> sti injectors and i.c are easyly ok for 400+hp??
any help?
been doing some hunting on the net and found a andy forest 20g td05???
full 3" exhaust system
uprated boost control solinoid or ebc
uprated fuel pump
anything else??? will turbo fit directly onto std flange, intake and oil feeds ect???
seen somewhere that 00> sti injectors and i.c are easyly ok for 400+hp??
any help?
#3
Scooby Regular
iTrader: (2)
Join Date: Sep 2002
Location: West Yorkshire
Posts: 2,977
Likes: 0
Received 0 Likes
on
0 Posts
20G turbo may just make 400bhp with supporting mods. 380 - 390 is more realistic.
I went for an 18G in the end and sold the 20G. Better mid range than the 20 although the latter will have better top end/ higher power figures on the rollers.
Ecutek map will be fine. My 53 plate sti was mapped by Bob Rawle and consists of:
3" decat exhaust
RCM downpipe
Harvey Smith up pipe and ported headers (wrapped)
Fuel pump
Andy Forrest 18G turbo
80mm RCM K&N filter
Uprated spark plugs
3 port boost solenoid
Running 1.45 boost and delta dash shows car running approx 390bhp/ 350lbs torque. Lag not an issue, mid range punch awesome. Standard sti injectors and top mount still in situ.
Next mods would be FMIC but decided too much outlay for very small gains.
HTH
I went for an 18G in the end and sold the 20G. Better mid range than the 20 although the latter will have better top end/ higher power figures on the rollers.
Ecutek map will be fine. My 53 plate sti was mapped by Bob Rawle and consists of:
3" decat exhaust
RCM downpipe
Harvey Smith up pipe and ported headers (wrapped)
Fuel pump
Andy Forrest 18G turbo
80mm RCM K&N filter
Uprated spark plugs
3 port boost solenoid
Running 1.45 boost and delta dash shows car running approx 390bhp/ 350lbs torque. Lag not an issue, mid range punch awesome. Standard sti injectors and top mount still in situ.
Next mods would be FMIC but decided too much outlay for very small gains.
HTH
#4
Scooby Regular
An Ecutek map will cope with those mods...
Turbo wise it is hard to advise against the TD05/20g but as another option Turbo Technics are close to releasing their range of hybrids for Subaru's...The T38 version will make 400 with ease and should also be available with a roller bearing option...This will mate with the standard uppipe and downpipe but can produce upto 500bhp depending on supporting modifications....
Turbo wise it is hard to advise against the TD05/20g but as another option Turbo Technics are close to releasing their range of hybrids for Subaru's...The T38 version will make 400 with ease and should also be available with a roller bearing option...This will mate with the standard uppipe and downpipe but can produce upto 500bhp depending on supporting modifications....
#6
cheers guys.
just want the biggest bang for the buck really, dont really want to be stripping the engine just yet.
the stock lumps good for a claimed 400hp so the 18g with the mods RLE listed should do me fine.
ta.
just want the biggest bang for the buck really, dont really want to be stripping the engine just yet.
the stock lumps good for a claimed 400hp so the 18g with the mods RLE listed should do me fine.
ta.
Thread
Thread Starter
Forum
Replies
Last Post
jobegold@hotmail.co.uk
ScoobyNet General
2
27 September 2015 09:44 PM