SX Fuel pressure regulator / fuel lines?
#1
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: Lancs / Manc
Posts: 534
Likes: 0
Received 0 Likes
on
0 Posts
SX Fuel pressure regulator / fuel lines?
Can anyone offer me any advice on the suitable connectors required to plumb in the above FPR to standard MY97 fuel lines? I know the instructions say they are a AN-6 but well that's as much as i know! (currently looking on LMA for suitable connectors).
http://www.sx-performance.com/15404I...44270411-1.pdf
LMA Motorsport - Products
Thanks
http://www.sx-performance.com/15404I...44270411-1.pdf
LMA Motorsport - Products
Thanks
#2
Scooby Regular
iTrader: (5)
Hello mate,
You need (I think) AN-6 to and 8mm barbed fitment, your fuel pipes will push on to these. Do you have a Pirtek UK shop near you? If so pop in and they will sort you out. Failing that try demon tweeks?
Unless you are replacing all of the rails for a one peice design or doing the parallel rails conversion, you need to buy the by-pass fitment that goes in place of the OEM fuel pressure regulator found in front of the turbo by the inlet manifold.
I did a fitting guide on here about a year ago but the photos are no longer stored online so its a bit useless. I am sure there have been other fitting guides posted since then tho.
The Hoff
You need (I think) AN-6 to and 8mm barbed fitment, your fuel pipes will push on to these. Do you have a Pirtek UK shop near you? If so pop in and they will sort you out. Failing that try demon tweeks?
Unless you are replacing all of the rails for a one peice design or doing the parallel rails conversion, you need to buy the by-pass fitment that goes in place of the OEM fuel pressure regulator found in front of the turbo by the inlet manifold.
I did a fitting guide on here about a year ago but the photos are no longer stored online so its a bit useless. I am sure there have been other fitting guides posted since then tho.
The Hoff
Last edited by The Hoff; 01 February 2007 at 01:00 PM.
#3
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: Lancs / Manc
Posts: 534
Likes: 0
Received 0 Likes
on
0 Posts
Hello mate,
You need (I think) AN-6 to and 8mm barbed fitment, your fuel pipes will push on to these. Do you have a Pirtek UK shop near you? If so pop in and they will sort you out.
Unless you are replacing all of the rails for a one peice design or doing the parallel lines conversion, you need to buy the by-pass fitment that goes in place of the OEM fuel pressure regulator found in front of the turbo by the inlet manifold.
You need (I think) AN-6 to and 8mm barbed fitment, your fuel pipes will push on to these. Do you have a Pirtek UK shop near you? If so pop in and they will sort you out.
Unless you are replacing all of the rails for a one peice design or doing the parallel lines conversion, you need to buy the by-pass fitment that goes in place of the OEM fuel pressure regulator found in front of the turbo by the inlet manifold.
#4
Scooby Regular
Thread Starter
Join Date: Jan 2005
Location: Lancs / Manc
Posts: 534
Likes: 0
Received 0 Likes
on
0 Posts
Aye, it's bookmarked m8 (not actually doing the work myself but want to make sure i have everything needed and at least an idea on what's involved).
Thread
Thread Starter
Forum
Replies
Last Post
Mattybr5@MB Developments
Full Cars Breaking For Spares
12
18 November 2015 07:03 AM
Pro-Line Motorsport
Car Parts For Sale
2
29 September 2015 07:36 PM